Manuals / JVC / TV and Video / VCR

JVC LPT0328 specifications 84 EN, Other Problems

Models: LPT0328

1 88

Download 88 pages 24.08 Kb

Page 84

84 EN			TROUBLESHOOTING (cont.)
OTHER PROBLEMS
	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
1.	Whistling or howling is heard from the	● The camcorder’s microphone is too	Position the camcorder so its microphone
	TV during camcorder recording.	close to the TV.	is away from the TV.
		● The TV’s volume is too high.	Turn the TV’s volume down.

2.	When scanning channels, some of	● Those channels have been designated to	If you need the skipped channels, restore
	them are skipped over.	be skipped.	them ( pg. 74).

3.	The channel cannot be changed.	● Recording is in progress.	Press 9 to pause the recording, change
			channels, then press 4 to resume
			recording.

4.	Channel settings that were made	● After the manual settings were made,	Perform manual setting again.
	manually seem to have changed or	Auto Channel Set was performed.
	disappeared.

5.	No channels are stored in the	● The TV aerial cable was not connected	Turn off the recorder once and connect
	recorder’s memory.	to the recorder when Auto Set Up was	the TV aerial cable to the recorder
		performed.	properly, then turn on the recorder again.
			The recorder will try Auto Set Up again
			( pg. 12).
		● The fully-wired 21-pin SCART cable was	Turn off the recorder once and connect
		not connected between TV and the	the fully-wired 21-pin SCART cable to the
		recorder when Preset Download was	recorder properly, then turn on the
		performed.	recorder again. Then perform Preset
			Download again ( pg. 14).

6.	The remote control won’t operate the	● The remote control brand setting is	Re-set the remote control to the correct
	TV or satellite receiver.	incorrect.	brand. ( pg. 40, 41)

ATTENTION

This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the recorder off and unplug the mains power cord. Then plug it in again and turn the recorder on. Take out the cassette. After checking the cassette, operate the unit as usual.

Image 84

JVC LPT0328 specifications 84 EN, Other Problems

Contents

Video Cassette Recorder Safety Precautions Moisture Condensation Front View Inside View of Front Panel Rear View ON-SCREEN Display Remote Control How To Use Remote Control LCDCheck the contents 10 ENSituate the recorder Connect the recorder to TV8To connect to a TV with S-VIDEO/AUDIO in connectors Plug the end of the mains power cord into a mains outletVideo Connection Auto Set Up 12 ENTurn on the recorder Select your countryPerform Auto Set Up Select the languagePress rt to select your language code Press rt to select Auto and press OK or ePerform Preset Download 14 ENSet the video channel Press rt to select CH - and press OK or eLanguage for the on-screen display Just ClockAccess the Main Menu screen Access the Country Set screenLanguage 16 ENInstalling Satellite Controller Situate the Satellite ControllerAttach the Satellite Controller Make connectionsSetting satellite receivers brand and channel 18 ENTV Auto Power On NexTView LinkVCR Auto Standby Direct Rec Basic Playback 20 ENVariable Speed Search Slow MotionHigh-Speed Turbo Search Pause during playback22 EN Skip SearchIndex Search Manual Index Mark/EraseNext Function Memory Digital TBC/NRRepeat Playback Manual TrackingAudio signal during TimeScan TimeScan24 EN Activate Variable Speed SearchTimeScan 26 EN Instant Timer Recording ITR Tape Remaining TimeEngage the Record-Pause mode 28 ENRetake Locate the start pointEngage the S-VHS ET mode Adjust the audio recording levelSuper VHS ET S-VHS ET Audio Recording Level ControlReceiving Stereo and Bilingual Programmes On-screen DisplayReceived Playback RecordingAccess the Showview display Access the Showview screenAccess the Showview Program screen 32 ENSet the VPS/PDC mode Engage the recorder’s timer modeSatellite Receiver Users Guide Program Number SetExpress Timer Programming 34 ENTo Timer-Record Weekly Or Daily Serials VPS/PDC RecordingEnter the channel position Press PR+36 EN Cancel or change programme setting Confirm the overlapping programmesSelect the programme to modify Overlapping programmes blink on the TV screenSelect the L-2 Select mode Recording modeProgramme Recording 38 ENRemote A/B Code Switching Remove the power supplySet the remote control code Re-supply the powerTV Multi-Brand Remote Control 40 ENSet the TV brand code Operate the TVSatellite Receiver Multi-Brand Remote Control Set the satellite receiver brand codeOperate the satellite receiver Navigation 42 ENNavigation Playback Check MemoryTurn Off Navigation Video Navigation Title ScreenCheck the memory Turn off NavigationAccess the Find Blank Space screen Edit Title44 EN Find Blank SpaceAccess the Edit Title screen Edit Tape TitleEntering Character Select the tape title46 EN Choice of CategorySelect the programme Enter the programme titleDelete Tape Data Delete Programme DataDelete the tape data Delete the programme dataAccess the Find Title screen Find Title48 EN Sort By Tape NumberAccess the Tape No. screen Access the Date screenSort By Date Select the programmeAccess the Category screen 50 ENSort By Category Category you want to watchSet the recorder’s input mode Set the edit modeEdit From a Camcorder Start the camcorderOutput/Input Set Select and L-2 Input Setting Decoder connectorAnother Video Recorder 54 ENRecorder Player Audio Dubbing 56 ENPre-recorded tape Audio-dubbed tape CD player, etcEngage the Audio Dubbing mode Start dubbingEnd Audio Dubbing Press AUX number key 0 and/or PR to select F-1 or S-1Insert Editing 58 ENSource tape Before Insert Editing Recording tape After Insert EditingEngage the Insert Editing mode AV Insert EditingLocate the end point Start EditingAccess the R.A.Edit screen 60 ENLoad the source cassette Start playback of the source cassetteMemory Capacity Prepare the recording deckStart Random Assemble Editing End Random Assemble Editing62 EN Start Synchro EditingPause Synchro Editing Press Synchro 7/79Access the Jlip ID No. Set screen Set the Jlip ID numberJlip ID Number ExamplesConnecting To a Satellite Receiver Simple ConnectionsPerfect Connections Satellite receiver Decoder Back of recorderSelect the input mode 66 ENConnect the decoder Set the tunerConnecting/Using a Stereo System Make connectionsMode Set Access the Mode Set screenSelect the mode Select the mode settingYou can set the B.E.S.T. Biconditional Equalised Signal This feature helps you to adjust the playback pictureWhen this function is set to ON, the timer is Off, and automatically disengaged when the recorder is70 EN For ExampleAbout Ntsc Playback Access the Auto Channel Set screen Tuner Set72 EN Auto Channel SetPerform Auto Channel Set View the Confirmation screenPress OK twice 74 EN Manual Channel SetWhen Receiving a Scrambled Broadcast Delete a Channel76 EN Set Stations aSet Stations B TV Station And ID List Station NameAccess the Video Channel Set mode Exit the Video Channel Set modeVideo Channel Set 78 ENShowview System Setup Guide Program Number SetGuide Program Number Enter the Guide Program numberAccess the Clock Set screen Clock Set80 EN Set the date and time Set Just ClockSet the source channel position for clock data Start the clock operationTroubleshooting 82 ENRecording Other Problems 84 ENPlayback 86 EN Preset Download Timer Warning Display TimeScan Tuner SetAV Insert Editing S.T. Picture System Clock SetInternational telephone Language code Country code