JVC LVT0870-006A Operating Video Components, VCR 1 VCR connected to the VCR 1 jacks, DVD player

Operating Video Components

IMPORTANT:

To operate JVC’s video components using this remote control:

•You need to connect JVC’s video components through the AV COMPU LINK jacks (see page 49) in addition to the connections using cables with RCA pin plugs (see pages 10 to 12).

•Some JVC’s VCRs can accept two types of the control signals— remote code “A” and “B.” Before using this remote control, make sure that the remote control code of the VCR connected to the VCR 1 jacks is set to code “A.”

–When another JVC’s VCR is connected to the VCR 2 or VIDEO jacks, set its remote control code to code “B.” (This remote control cannot emit the control signals of code “B.”)

•When using the remote control, aim the remote control directly at the remote sensor on each component, not on the receiver.

A/V CONTROL RECEIVER

CATV/DBS		VCR1	TV	AUDIO
DVD	DVD MULTI		CD	FM/AM
TV/DBS		VIDEO	CDR	PHONO
VCR1		VCR2	TAPE/MD	USB
SURROUND		DSP	SURR/DSP ANALOG/DIGITAL
			OFF	INPUT
ANALOG		BASS	∗FRONT•L	∗FRONT•R
DIRECT		BOOST
		1	2	3
			MENU
SOUND		TEST	∗CENTER	∗SUBWFR
		4	5	6
			ENTER
DIMMER			∗SURR•L	∗SURR•R
		7/P	8	9
MUTING	∗DIGITALEQ ∗SBACK•L ∗SBACK•R
		10	0	+10
		RETURN	FMMODE	100+
CATV/DBS
CONTROL		+	+	+
TV/VIDEO CH/∗LEVEL TV VOL				VOLUME
		−	−	−
TEXT		MENU	PLAY
DISPLAY				EXIT
REC		/REW	PAUSE	FF/
PAUSE
			SET
SLEEP		DOWN – TUNING – UP
			STOP	CONTROL

RM-SRX8020JREMOTE CONTROL

Note:

When you press one of the source selecting buttons, the operation mode appears on the display window. For example, the above illustration shows the remote control now works for VCR 1 operation.

Buttons	Indications
VCR1		VCR1
DVD or DVD MULTI		DVD
TV/DBS		TV
CONTROL (repeatedly)*	VCR1		TAPE

CDDSC CDR

*By pressing CONTROL repeatedly, you can select “VCR1,” “TAPE,” “CDR” or “CDDSC” as the source.

VCR 1 (VCR connected to the VCR 1 jacks)

You can always perform the following operations:

VCR1	:Turn on or off the VCR 1 (VCR connected to
	the VCR 1 jacks).

After pressing VCR1 (or selecting “VCR1” by pressing CONTROL repeatedly), you can perform the following operations on the VCR 1 (VCR connected to the VCR 1 jacks):

1 – 9, 0	:Select the TV channels on a VCR.
3 PLAY	:Start playing.
REW	:Rewind a tape.
FF	:Fast wind a tape.
7 STOP	:Stop playing or recording.
8 PAUSE	:Pause playing. To resume, press 3 PLAY.
REC PAUSE	:Enter recording pause by pressing this button.
	To start recording again, press this button then
	3 PLAY.
CH +/–	:Change the TV channels on the VCR.

Note:

You can use either VCR1 or CONTROL to activate the buttons listed above. If you press VCR1, the playing source also changes. On the other hand, if you press CONTROL repeatedly to select “VCR1,” the playing source does not change.

DVD player

After pressing DVD or DVD MULTI, you can perform the following operations on a DVD player:

3 PLAY :Start playing.

4:Return to the beginning of the current (or

previous) chapter.

¢:Skip to the beginning of the next chapter.

7 STOP :Stop playing.

8PAUSE :Pause playing. To resume, press 3 PLAY.

After pressing DVD or DVD				∗FRONT•L	∗FRONT•R
MULTI, these buttons can be used				2	3
for the DVD menu operations.			TEST	∗CENTER	MENU
					∗SUBWFR
	Note:		4	5	6
				ENTER
				∗SURR•L
For detailed menu operations, refer				8
to the instructions supplied with the
discs or the DVD player.
TV
You can always perform the following operations:
TV		:Turn on or off the TV.
TV VOL +/–		:Adjust the volume.
TV/VIDEO		:Set the input mode (either TV or VIDEO).

After pressing TV/DBS, you can perform the following operations on a TV:

CH +/–	:Change the channels.
1 – 9, 0, 100+	:Select the channels.
RETURN	:Alternate between the previously selected
	channel and the current channel.

53