To change the transmittable signals for operating a CATV converter or DBS tuner
1.Press and hold CATV/DBS 
.
2.Press CATV/DBS CONTROL.
“CALL” appears on the remote control display window.
3 Enter a manufacturer’s code using buttons 1–9, and 0.
See the following lists to find the code.
4. Release CATV/DBS 
.
The following buttons can be used for operating the CATV converter and DBS tuner:
CATV/DBS | :Turn on and off the CATV converter |
| or DBS tuner. |
CH +/– | :Change the channels. |
1 – 10, 0, 100+ (+10) | :Select the channels. |
| The |
| ENTER button if your equipment |
| requires pressing ENTER after |
| selecting a channel number. |
Note:
Refer also to the manual supplied with your CATV converter or
DBS tuner.
5. Try to operate your CATV converter or DBS tuner by pressing CATV/DBS 
.
When your CATV converter or DBS tuner turns on or off, you have entered the correct code.
If there are more than one code listed for your brand of
CATV converter or DBS tuner, try each one until the correct one is entered.
Note:
You cannot preset the signals for both the CATV converter and DBS
tuner at the same time.
| For DBS tuner | |
|
|
|
Manufacturer |
| Codes |
JVC |
| 56*, 57, 67 |
AMSTRAD |
| 43, 44, 45, 46, 47, 48, 49 |
BLAUPUNKT |
| 30 |
ECHOSTAR |
| 50, 51, 67 |
GOLDSTAR |
| 31 |
GRUNDIG |
| 32, 33 |
HIRSHMANN |
| 48, 52, 53, 54, 55 |
INSTRUMENT |
| 68 |
ITT/NOKIA |
| 34 |
KATHREIN |
| 52, 58, 59, 60, 61, 62, 63 |
NEC |
| 35, 36 |
ORBITECH |
| 48 |
PHILIPS |
| 37, 38 |
RCA |
| 65 |
SAMSUNG |
| 39, 40 |
SCHWAIGER |
| 61, 64 |
SIEMENS |
| 41, 42 |
SONY |
| 66 |
TECHNISAT |
| 48 |
*Initial setting
For CATV converter
Manufacturer | Codes |
|
|
GENERAL INSTRUMENT | 06, 07, 08, 09, 10, 11, |
| 12, 13, 14, 29 |
HAMLIN/REGAL | 01, 02, 03, 04, 05 |
JERROLD | 06, 07, 08, 09, 10, 11, |
| 12, 13, 14 |
OAK | 15, 16, 17 |
PANASONIC | 18, 19, 20 |
PIONEER | 21, 22 |
SCIENTIFIC ATLANTA | 23, 24, 25 |
TOCOM | 26 |
ZENITH | 27, 28 |
Manufacturers’ codes are subject to change without notice. If they are changed, this remote control cannot operate the equipment.
To change the transmittable signals for operating another manufacturer’s VCR
1.Press and hold VCR1 
.
2.Press VCR1.
“CALL” appears on the remote control display window.
3. Enter manufacturer’s code using buttons 1–9, and 0.
See the list on the next page to find the code.
4. Release VCR1 
.
The following buttons can be used for operating the VCR:
VCR1 | :Turn on and off the VCR. |
After pressing VCR1, you can perform the following operations on the VCR:
CH +/– | :Change the TV channels on the |
| VCR. |
1 – 10, 0, 100+ (+10) | :Select the TV channels. |
| The |
| ENTER button if your VCR requires |
| pressing ENTER after selecting a |
| channel number. |
3 PLAY | :Start playback. |
REW | :Rewind a tape. |
FF | :Fast wind a tape. |
7 STOP | :Stop playing or recording. |
8 PAUSE: | :Pause playing. To resume, press |
| 3 PLAY. |
REC PAUSE | :Enter recording pause by pressing |
| this button. |
| To start recording again, press this |
| button then 3 PLAY. |
Note:
Refer also to the manual supplied with your VCR.
5. Try to operate your VCR by pressing VCR1 
.
When your VCR turns on or off, you have entered the correct code.
If there are more than one code listed for your brand of
VCR, try each one until the correct one is entered.
55
