JVC LVT1002-001B SCART connection, RX-ES1SL TV, Getting started, SCART Terminal Specifications

Getting started

SCART connection

SCART cable (supplied: 1 cable)

VCR

AM LOOP

VCR

AV IN / OUT

TV

DIGITAL 1

CENTER

SURROUND

FRONT

ANTENNA

(DVD)

SPEAKER

SPEAKERS

SPEAKERS

RIGHT LEFT RIGHT LEFT

AM EXT CENTER

AUDIO

DIGITAL 3

DIGITAL 2

DIGITAL IN

(TV)

(STB)

L

L

DVD

AV IN

STB

CAUTION:

SPEAKER

R

R

SUBWOOFER

IMPEDANCE

D

OUT

8 ~ 16

SUB

SURR

N

FRONT

WOOFER

(REAR)

RX-ES1SL

TV

VCR AV IN/OUT TV

DVD AV IN STB STB

*

See below.

For TV and video format

•When the TV is equipped with the multiple SCART terminals, refer to the TV manual to check the available video signals for each terminal, then connect SCART cable correctly.

•This receiver cannot convert the video signals (S-video or Composite). When the video signal of one video component is different from that of the other (for example, one is S-video, the other is Composite), you may not see the pictures appropriately. In this case, unify the video signals of all the video components into S-video or Composite, or you need to switch the video signal of TV each time you change the source.

For T-V LINK

•You can use the T-V LINK function if you connect a T-V LINK compatible TV and VCR to this receiver with a fully wired SCART cables. For details on T-V LINK, refer also to the manuals supplied with the TV and the VCR.

•Connect a SCART cable to EXT-2 terminal on your JVC’s T-V LINK compatible TV for the T-V LINK function.

•Some TV, VCR, STB and DVD players’ support the data communication like T-V LINK. For complete details, refer also to the manuals supplied with these components.

*For an analogue decoder

To watch or record a scrambled program on your VCR, connect the analogue decoder to your VCR and select the scrambled channel on your VCR.

If there is not an appropriate terminal for the decoder connection on your VCR, connect the decoder to your TV.

Refer also to the manuals supplied with these components.

*For recording pictures from STB

When you connect a STB and a VCR directly with a SCART cable, you can record the pictures from the STB onto VCR without using the STB menu screens. For details, refer also to the manuals supplied with the STB.

For digital sounds

To reproduce the digital sound, use both the digital connection and the SCART cable connection (see pages 8 and 9).

SCART Terminal Specifications

		TV	VCR	STB	DVD
AUDIO	L/R	◯	◯	◯	◯
IN	Composite	◯	◯	◯	◯
		−
VIDEO	S-video		◯	◯	◯
	RGB	−	◯	◯	◯
AUDIO	L/R	◯*1	◯*1
OUT	Composite ◯*1*2 ◯*1*2
			−
VIDEO	S-video	◯*2
	RGB	◯*2	−
T-V LINK		◯*3	◯*3	◯*3	◯*3

*1 The signals input from a SCART terminal cannot be output through the same SCART terminal.

*2 The video format of the output video signals are consistent with that of the input video signals. For example, if S-video signals are input to this receiver, no signals other than S-video signals can be output from this receiver.

Refer to the manuals supplied with the video components to check the setting of the input/output video signals.

*3 The signals for the T-V LINK function are always going through the receiver.

CONTINUED ON THE NEXT PAGE

9