Troubleshooting
Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC’s service center.
PROBLEM | POSSIBLE CAUSE | SOLUTION |
|
|
|
The display does not light up. | The power cord is not plugged in. | Plug the power cord into an AC outlet. |
|
|
|
No sound from speakers. | Speaker signal cables are not connected. | Check speaker wiring and reconnect if necessary. (See |
|
| pages 9 and 10.) |
The SPEAKERS ON/OFF 1 and SPEAKERS ON/OFF 2 buttons are not set correctly.
Press SPEAKERS ON/OFF 1 and SPEAKERS ON/ OFF 2 correctly. (See page 17.)
| An incorrect source is selected. | Select the correct source. |
|
| ||||
|
|
|
|
|
| |||
| Muting is activated. | Press MUTING to cancel the mute. (See page 20.) |
| |||||
|
|
|
|
|
| |||
| An incorrect input mode (analog or | Select the correct input mode (analog or digital). (See |
| |||||
| digital) is selected. | page 17.) |
|
|
| |||
|
|
|
|
|
| |||
Sound from one speaker only. | Speaker signal cables are not connected | Check speaker wiring and reconnect if necessary. (See |
| |||||
| properly. | pages 9 and 10.) |
|
| ||||
|
|
|
|
|
| |||
Continuous hiss or buzzing during FM | Incoming signal is too weak. | Connect an outdoor FM antenna or contact your |
| |||||
reception. |
| dealer. (See page 8.) |
|
| ||||
|
|
|
|
|
|
| ||
| The station is too far away. | Select a new station. |
|
| ||||
|
|
|
|
|
| |||
| An incorrect antenna is used. | Check with your dealer to be sure you have the correct |
| |||||
|
| antenna. |
|
|
| |||
|
|
|
|
|
|
| ||
Noise is heard during FM/AM reception. | Antennas are not connected properly. | Check connections. (See page 8.) |
|
| ||||
|
|
|
|
|
| |||
| Ignition noise from automobiles. | Move the antenna farther from automobile traffic. |
| |||||
|
|
|
|
|
|
| ||
No sound effect such as Surround mode, | Analog Direct is turned on. | Turn off Analog Direct. (See page 19.) |
|
| ||||
DSP mode and Digital Equalization. |
|
|
|
|
|
|
|
|
DVD MULTI is selected as the source. | Select the source other than DVD MULTI. |
|
| |||||
|
|
| ||||||
|
|
|
|
|
|
| ||
EX/ES | Software or setting is not for Dolby | Play back software bearing the mark | or |
| ||||
be done for Dolby Digital EX or DTS ES | Digital EX or DTS ES software. |
|
|
| . |
|
|
|
|
|
|
|
|
| |||
software. |
| Set “EX/ES” setting to “ON.” (See page 35.) |
| |||||
|
|
|
|
|
|
|
| |
“OVERLOAD” starts flashing on the | Speakers are overloaded because of high | 1. | Press | STANDBY/ON on the front panel to |
| |||
display. | volume. |
|
| turn off the receiver. |
|
| ||
|
| 2. Stop the playback source. |
|
| ||||
|
| 3. | Turn on the receiver again, and adjust the volume. |
|
Speakers are overloaded because of short circuit of speaker terminals.
Press STANDBY/ON on the front panel to turn off the receiver, then check the speaker wiring.
If “OVERLOAD” does not disappear, unplug the AC power cord, then plug it back again.
If speaker wiring is not
The STANDBY lamp lights up after turning on the power, and soon the receiver turns off again (into standby mode).
The receiver is overloaded because of a high voltage.
Press STANDBY/ON on the front panel to turn off the receiver. After unplugging the AC power cord, consult your dealer.
Remote control does not work.
There is an obstruction between the | Remove the obstruction. |
remote sensor on the receiver and the |
|
remote control. |
|
|
|
Batteries are weak. | Replace batteries. (See page 7.) |
|
|
Remote control does not work as you intend.
An incorrect remote control operation mode is selected.
Select the correct remote control operation mode. (See pages 42 to 48.)
49