JVC LVT1007-010A[A] manual Reinforcing the Bass, Muting the Sound, Changing the Display Brightness

The following basic operations are possible only using the remote control.

Reinforcing the	BASSBOOST
	1	2	3
Bass	4	5	6
	7/P	8	9
	SOUND	0
	10/0		+10

	MUTING	Muting the
		Sound
Using the Sleep	SLEEP	Changing
Timer	DIMMER
		the Display
		Brightness

Reinforcing the Bass

You can boost the bass level.

•Once you have made adjustment, it is memorized for each source.

1.Press SOUND.

The 10 keys are activated for sound adjustments.

2.Press BASS BOOST to turn on Bass Boost. The BASS BOOST indicator lights up.

•Each time you press the button, Bass Boost turns on (“BOOST ON”) and off (“BOOST OFF”) alternately.

You can use the BASS BOOST button on the front panel.

When the Bass Boost is activated, the lamp on the button lights up.

•Each time you press the button, Bass Boost turns on and off.

Notes:

•This function affects only the sounds from the front speakers, center speaker, and subwoofer.

•When Analog Direct is activated (see page 19), the Bass Boost is canceled temporarily.

Muting the Sound

Press MUTING to mute the sound through all speakers and headphones connected.

“MUTING” appears on the display and the volume turns off (the VOLUME level indicator goes off).

To restore the sound, press MUTING again.

•Turning MASTER VOLUME on the front panel or pressing VOLUME +/– on the remote control also restores the sound.

Changing the Display Brightness

You can dim the display.

Press DIMMER.

•Each time you press the button, the brightness level of the display change as follows:

Dimmer Much dimmer

Canceled

(Normal display)

Using the Sleep Timer

Using the Sleep Timer, you can fall asleep while listening to music. When the shut-off time comes, the receiver turns off automatically.

Press SLEEP repeatedly.

The SLEEP indicator lights up on the display, and the shut-off time changes in 10 minutes intervals:

10 20 30 40 50 60 70 80 90

0(Canceled)

To check or change the time remaining until the shut-off time:

Press SLEEP once.

The remaining time until the shut-off time appears in minutes.

•To change the shut-off time, press SLEEP repeatedly.

To cancel the Sleep Timer:

Press SLEEP repeatedly until “SLEEP 0min” appears on the display. (The SLEEP indicator goes off.)

•Turning off the power also cancels the Sleep Timer.

Recording a source

For analog-to-analog recording

You can record any analog playback source onto the recording components connected to the audio output jacks on the rear of this unit at the same time.

For digital-to-digital recording

You can record the currently selected digital input source through the receiver to a digital recording device connected to the DIGITAL OUT terminal.

Notes:

•Analog-to-digital and digital-to-analog recordings are not possible.

•The output volume level, Midnight Mode (see page 18), Bass Boost (see the left column), Digital Equalization (see page 30), Surround modes and DSP modes (see pages 32 to 37) cannot affect the recording.

Basic adjustment auto memory

This receiver memorizes sound settings for each source—

•when you turn off the power,

•when you change the source, and

•when you assign the source name (see page 19).

When you change the source, the memorized settings for the newly selected source are automatically recalled.

The following can be stored for each source:

•Analog/digital input mode (see pages 17 and 18)

•Input attenuator mode (see page 18)

•Analog Direct (see page 19)

•Digital Equalization (see page 30)

•Speaker channel output levels (see page 30)

•Surround and DSP mode selection (see pages 35 and 37)

•Bass Boost setting (see the left column)

Notes:

•If the source is FM or AM, you can assign a different setting for each band.

•If you want to memorize the volume level with the above settings, set One Touch Operation to “ON” (see page 28).

20