5
6
INPUT SELECT
STANDBY
POWER
INPUT
ADJUST
CONFIG
PICTURE
CONTROL
OUTPUT
SETUP
MENU EXIT
16:94:3
AUTO
VIDEO 1S-VIDEO 1COMP 1HDMI 2
VIDEO 2S-VIDEO 2COMP 2HDMI 3
ENTER
HDMI 4
BORDER CROP
INFO CURTAIN
MEMORIES
RGBHV
HDMI 1SDI
ASPECT
ZOOMPAN
ON/OFF
DISPLAY
PROFILES
VIEWING
MODES
INPUT
ASPECT
RATIO
TEST PATTERN
ENTER
Standby
Info
Curtain
Output Setup
Configuration
Picture Control
Input Adjust
Menu
Border
Zoom
Input Select
(HDMI 1, HDMI 2, HDMI 3, HDMI 4,
Component 1, Component 2,
RGBHV/Component,
S-Video 1, S-Video 2,
Video 1, Video 2, AUTO)
Aspect
Exit
Crop
Pan
Power
Input Aspect
Ratio
Viewing Modes
Display Profiles
4:3
16:9
Test Patterns
(Left, On/Off, Right)
5
26
17
*
32
4
20
21
21
6
5
5
28
26
25
22
4
4
20
18
20
18
21
Remote Control Overview
For additional information about the functions of these buttons, turn to the pages listed below.
An asterisk (*) indicates a feature that has not yet been implemented.
Power/Standby Buttons
The rs-Vp2 remote has a Power and a Standby button. The Power button always turns the rs-Vp2
on and the Standby button always put the unit into Standby mode.
Info Button
This rs-Vp2 has an ‘info’ screen which brings up a window on the connected display which contains
important input and output information which can help with troubleshooting. The software version
which is loaded in the unit will also be displayed on this window and on the front panel display of the
RS-VP2.
Curtain Button
The rs-Vp2 remote has a Curtain button which allows you to close a ‘curtain’ over the image. This
feature is especially useful when an image is paused on a display susceptible to burn-in or a transition
while switching inputs as part of a macro on a universal remote or automation system.

Discrete IR Codes and Serial Automation Protocol

almost all commands that are available in the on screen display can be executed discretely using a
programmable IR remote control or automation system connected via an RS232 serial connection.
These codes are available at www.jvc.com/pro.

Non-Volatile Memory Settings

The RS-VP2 stores a variety of user settings in non-volatile memory. Non-volatile memory
retains its contents when power is lost. There is one group of system settings and one group of user
settings.
Installation Guidelines
Take special care with the RS-VP2 installation to ensure optimal performance. Pay particular attention to
the bulleted items that begin below and to other precautions that appear throughout this guide.
Do . . .
Install the RS-VP2 on a solid, at, level surface such as a table or shelf.
You can also install the RS-VP2 in a standard 19” equipment rack using an optional
rack-mount kit available from authorized JVC resellers or directly from JVC.
Select a dry, well-ventilated location.
Use only the included external power supply.
Avoid excessive humidity, sudden temperature changes or temperature extremes.
Use only accessories recommended by the manufacturer to avoid re, shock or other hazards.
Unplug your RS-VP2 before cleaning. Use a damp cloth for cleaning.
Don’t . . .
Install the RS-VP2 on an unstable surface or one that is unable to support all
four of its feet, unless it is installed in an equipment rack.
Stack the RS-VP2 directly above heat-producing equipment such as power
ampliers or other components that generate heat during use.
Expose the RS-VP2 to a high temperatures, humidity, steam, smoke, dampness,
or excessive dust. Avoid installing the RS-VP2 near radiators and other heat
producing appliances.
Install the RS-VP2 near unshielded TV or FM antennas, cable TV decoders, and
other RF -emitting devices that might cause interference.
Place the RS-VP2 on a thick rug or carpet or cover the RS-VP2 with cloth.
This might prevent proper cooling.
Attempt to service this unit. Instead, disconnect it and contact your Authorized JVC
Reseller or contact JVC directly.
Open or remove unit panels or make any adjustments not described in this manual.
Attempting to do so could expose you to dangerous electrical shock or other hazards.
It may also cause damage to your RS-VP2.
Obstruct the front panel IR receiver window shown in “Remote Control Overview”.
Do not attempt to use the remote control out of line of sight with the IR receiver.
Doing so will cause improper operation.