JVC RX-7010RBK manual To select the delay time of the rear speaker output, Press Control UP 5/DOWN

2. Press CONTROL UP 5/DOWN ° CONTROL

DOWN UP

to select the delay time of the rear speaker output.

•Press CONTROL UP 5to increase the delay time from 0 msec (“R_DELAY 0MS”) to

15 msec (“R_DELAY 15MS”).

•Press CONTROL DOWN °to decrease the delay time from 15 msec (“R_DELAY 15MS”) to 0 msec (“R_DELAY 0MS”).

Low Frequency Effect Attenuator Setting

If the bass sound is distorted while playing back a source using Dolby Digital or DTS Digital Surround, follow the procedure below.

On the front panel ONLY:

1. Press SETTING repeatedly until	T SETTING
“LFE ATT” (Low Frequency
Effect Attenuator) appears on the
display.

Notes:

•Rear delay time is not valid for the DVD MULTI playback mode.

•You cannot adjust the rear delay time when you have set “REAR SPK” to “NO.”

Crossover Frequency Setting

Small speakers cannot reproduce the bass sound very well. So, if

The display changes to show the current setting.

2.Press CONTROL UP 5/DOWN ° to select the low frequency effect attenuator level.

•Each time you press the button, the display changes to show the following:

CONTROL

DOWN UP

you have used a small speaker for any of the front, center, and rear channels, this receiver automatically reallocate the bass elements, originally assigned to the channel for which you have connected the small speaker, to another channel (for which you have connected the large speaker).

To use this function properly, you need to set the crossover frequency level according to the size of the small speaker connected.

•If you have selected “LARGE” for all speakers (see page 14), this function is set to “OFF” and cannot be adjusted.

On the front panel ONLY:

1. Press SETTING repeatedly until	ST SETTING
“CROSSOVER FRQ” (Crossover
Frequency) appears on the display.
The display changes to show the current setting.

2. Press CONTROL UP 5/DOWN °	CONTROL
	DOWN UP
to select the crossover frequency
level according to the size of the
small speaker connected.

•Each time you press the button, the display changes to show the following:

80HZ100HZ120HZ

0dB 10dB

0dB: Normally select this.

10dB: Select this when the bass sound is distorted.

Notes:

•Low frequency effect attenuator is not valid for the DVD MULTI playback mode.

•This function takes effect only when the subwoofer (LFE) signals come in, (with “SUBWOOFER” set to “YES.”)

Dynamic Range Compression Setting

You can compress the dynamic range (difference between maximum sound and minimum sound) of the reproduced sound. This is useful when enjoying surround sound at night.

•This function takes effect only when playing back a source using Dolby Digital.

On the front panel ONLY:

1. Press SETTING repeatedly until	ST SETTING
“D_RANGE COMP” (Dynamic

Range Compression) appears on the display.

• Use the following comments as reference when adjusting.

80HZ: Select this when the cone speaker unit built in the speaker is about 4 3/4 inches (12 cm).

100HZ: Select this when the cone speaker unit built in the

speaker is about 3 15/16 inches (10 cm).

The display changes to show the current setting.

2.Press CONTROL UP 5/DOWN ° to select the appropriate item about the compression level.

•Each time you press the button, the display changes to show the following:

CONTROL

DOWN UP

120HZ: Select this when the cone speaker unit built in the speaker is about 3 3/16 inches (8 cm).

Note:

Crossover frequency is not valid for the DVD MULTI playback mode

and HEADPHONE mode.

OFF MID MAX

OFF: Select this when you want to enjoy surround with its full dynamic range. (No effect applied.)

MID: Select this when you want to reduce the dynamic range a little. (Factory setting.)

MAX: Select this when you want to apply the compression effect fully. (Useful at night.)

Note:

Dynamic Range Compression is not valid for the DTS Digital

Surround and DVD MULTI playback mode.

15