JVC RX-7012RSL manual Operating JVC’s Audio/Video Components, Operating Audio Components, Tuner

Operating JVC’s Audio/Video Components

You can operate JVC’s audio and video components with this receiver’s remote control, since control signals for JVC components are preset in the remote control.

Operating Audio Components

IMPORTANT:

To operate JVC’s audio components using this remote control:

•You need to connect JVC audio components through the COMPU LINK (SYNCHRO) jacks (see page 31) in addition to the connections using cables with RCA pin plugs (see pages 5 and 6).

•Aim the remote control directly at the remote sensor on the receiver.

•If you use the buttons on the front panel, the remote control will not operate that source. To operate a source with the remote control, the source must be selected using source selecting buttons on the remote control.

•To operate the cassette deck or CD recorder using the COMPU LINK remote control system, set the source name correctly. (See page 13.)

•Refer also to the manuals supplied with your components.

CATV/DBS	VCR		TV	AUDIO
DVD	DVD MUILTI		CD	FM/AM
TV/DBS	VCR		TAPE/CDR	PHONO
− BASS +			−TREBLE+
SURROUND	DSP	ANALOG/DIGITAL		SLEEP
ON/OFF	MODE		INPUT
BASSBOOST	EFFECT		– CENTER+
	1		2	3
			MENU
	TEST		– REAR• L+
	4		5	6
			ENTER
SOUND			– REAR• R+
	7/P		8	9
MUTING			–SUBWOOFER+
	10		0	+10
	RETURN		FMMODE	100+
CATV/DBS
CONTROL	+		+	+
TV/VIDEO	CH		TV VOL	VOLUME
	−		−	−
+			PLAY
TUNING	/REW		PAUSE	FF/
−
REC	PTY–	PTY SEARCH PTY+
PAUSE
			STOP	CONTROL
			DISPLAY

RM-SRX7010R

A/V CONTROL RECEIVER

*When you press one of the following buttons, the remote control operation mode appears on the display window for about 10 seconds.

	Ex.: When you
	press CD button
Buttons on the Remote Control	Remote Control Operation Mode
FM/AM	TUNER
CD	CD
PHONO	PHONO
TAPE/CDR	TAPE
DVD	DVD
DVD MULTI	DVD
TV/DBS	TV
VCR	VCR
CATV/DBS CONTROL	DBS
CONTROL	Current setting or VCR or TAPE
	or CDDSC
SOUND	SOUND

Tuner

You can always perform the following operations:

FM/AM: Alternates between FM and AM (MW/LW).

After pressing FM/AM, you can perform the following operations:

1 – 10, +10: Selects a preset channel number directly. For channel number 5, press 5.

For channel number 15, press +10, then 5. For channel number 20, press +10, then 10.

TUNING +/–: Tunes into stations.

FM MODE: Changes the FM reception mode.

PTY SEARCH: Searches for a program by PTY codes.

PTY +/–: Selects the PTY codes.

DISPLAY: Shows the RDS signals.

Sound control section (Amplifier)

You can always perform the following operations:

SURROUND ON/OFF: Turns on or off the Surround modes –

	Dolby Pro Logic, Dolby Digital, and
	DTS Digital Surround.
DSP MODE:	Selects the DSP modes.

After pressing SOUND, you can perform the following operations:

SUBWOOFER +/–: Adjusts the subwoofer output level.

CENTER +/–:	Adjusts the center speaker output level.
REAR•L +/–:	Adjusts the left rear speaker output level.
REAR•R +/–:	Adjusts the right rear speaker output level.
EFFECT:	Selects the effect level.
TEST:	Turns on or off the test tone output.

Note:

After adjusting sounds, press the corresponding source selecting button to operate your target source by using the 10 keys; otherwise, the 10 keys cannot be used for operating your target source.

CD player

After pressing CD, you can perform the following operations on the CD player:

PLAY3:	Starts playing.
4:	Returns to the beginning of the current (or
¢:	previous) track.
	Skips to the beginning of the next track.
STOP7:	Stops playing.
PAUSE8:	Pauses playing. To release it, press PLAY3.
1 – 10, +10:	Selects a track number directly.
	For track number 5, press 5.
	For track number 15, press +10, then 5.
	For track number 20, press +10, then 10.
	For track number 30, press +10, +10, then 10.

32