Changing the source name
When you connect a CD recorder to the TAPE/CDR jacks on the rear panel, change the source name shown on the display.
1Press TAPE/CDR (SOURCE NAME).
• Make sure “TAPE” appears on the display.
2Press and hold SOURCE NAME (TAPE/CDR) until “ASSIGN CDR” appears on the display.
Remote
NOT
TAPE/CDR
SOURCE NAME
TAPE/CDR
SOURCE NAME
Adjusting the Volume
On the front panel:
MASTER VOLUME
To increase the volume,
turn MASTER VOLUME clockwise.
To decrease the volume,
turn it counterclockwise.
From the remote control:
To increase the volume, press VOLUME +.
English
To change the source name from “CDR” to “TAPE,” repeat the
same procedure above (in step 1, make sure “CDR” appears on the display).
Note:
Without changing the source name, you can still use the connected component. However, there may be some inconvenience:
–“TAPE” will appear on the display when you select the CD recorder.
–You cannot use the digital input (see page 14) for the CD recorder.
–You cannot use the COMPU LINK remote control system (see page 31) to operate the CD recorder.
Selecting different sources for picture and sound
You can watch picture from a video component while listening to sound from another component.
Press one of the audio source selecting buttons—
CD, TAPE/CDR, FM, AM (or FM/AM on the remote control), while watching the picture from a video component such as the VCR, or DVD player, etc.
To decrease the volume, press VOLUME –.
VOLUME
CAUTION:
Always set the volume to the minimum before starting any source. If the volume is set at its high level, the sudden blast of sound energy can permanently damage your hearing and/or ruin your speakers.
Note:
The volume level can be adjusted within the range of “0” (minimum) to “50” (maximum).
Selecting the Front Speakers | Remote |
| NOT |
When you have connected two pairs of the front speakers, you can select which to use.
SPEAKERS ON/OFF
1 | 2 |
|
|
| TAPE/CDR | CD | DVD | DVD MULTI |
DVD MULTI | DVD | VCR | TV SOUND |
|
|
|
CD | TAPE/CDR | FM | FM/AM | TV SOUND | VCR |
|
AM |
|
|
|
SOURCE NAME
On the front panel | From the remote control |
Notes:
•Once you have selected a video source, pictures of the selected source are sent to the TV until you select another video source.
•This function can use only when selecting the
To use the speakers connected to the FRONT SPEAKERS 1
terminals, press SPEAKERS ON/OFF 1 so that the SPK 1 indicator lights up on the display. (Make sure that the SPK 2 is not lit on the display.)
To use the speakers connected to the FRONT SPEAKERS 2
terminals, press SPEAKERS ON/OFF 2 so that the SPK 2 indicator lights up on the display. (Make sure that the SPK 1 is not lit on the display.)
To use both set of the speakers, press SPEAKERS ON/OFF 1 and 2 so that the SPK 1 and SPK 2 indicators light up on the display. To use neither set of the speakers, press SPEAKERS ON/OFF
1 and 2 so that the SPK 1 and SPK 2 indicators disappear from the display.
Notes:
•If you select any of the Surround modes while using both the speakers connected to the FRONT SPEAKERS 1 and 2 terminals, the speakers connected to the FRONT SPEAKERS 2 terminals are deactivated.
•While the Surround mode is in use, you can only select either the speakers connected to the FRONT SPEAKERS 1 or 2 terminals.
•If you select DVD MULTI as the source while using both the speakers connected to the FRONT SPEAKERS 1 and 2 terminals, the speakers connected to the FRONT SPEAKERS 2 terminals are deactivated.
•When selecting “DVD MULTI” as the source, you can only select either the speakers connected to the FRONT SPEAKERS 1 or 2 terminals.
11