Basic Settings
CONTROL |
|
|
|
|
|
|
5/°/3/2 | Display |
|
|
|
|
|
STANDBY |
|
| ||||
TV DIRECT | DVD | STB | VCR | TV | TAPE | FM/AM |
STANDBY/ON |
|
|
|
|
|
|
|
| CONTROL |
| ANALOG | L | C | R | PRO LOGIC | SLEEP | RDS | EON | TA | HEWS | INFO | TUNED ST | AUTO | MUTING |
|
|
|
|
|
|
| LPCM | SUBWFR LFE DSP |
|
|
|
|
|
|
|
| MH |
|
|
| |||
|
|
|
| DOLBY D | LS | S | RS | DGTL AUTO |
|
|
|
|
|
|
|
| KH | INPUT | SURROUND | DSP |
SETTING | ADJUST |
| MEMORY | DTS | INPUT ATT |
|
|
|
|
|
|
|
| VOL | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ANALOG/DIGITAL | ON/OFF | MODE | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| MASTER VOLUME |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| INPUT ATT |
|
|
D I G I T A L |
|
|
| DVD |
|
| STB |
| VCR |
|
| TV |
| TAPE |
|
| FM/AM |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
S U R R O U N D D I G I T A L |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SETTING |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Low Frequency Effect Attenuator — LFE
If the bass sound is distorted while playing back software using Dolby Digital or DTS Digital Surround, follow the procedure below.
•This function takes effect only when the subwoofer (LFE) signals come in, (with “SUBWFR” set to “YES”).
Before you start, remember...
There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
1Press SETTING.
SETTINGThe CONTROL buttons now work for basic settings.
2Press CONTROL ° (or 5) repeatedly until “LFE (Low Frequency Effect)” (with the current setting)* appears on the display.
CONTROL
C
O |
VOL 
*“0” is the initial setting. If you have already changed the setting,
3Press CONTROL 3(or 2) to select the LFE attenuator level.
• Each time you press the button, the LFE attenuator level
changes as follows:
CONTROL
ANALOG | L | C | R | PRO LOGIC |
|
LPCM | SUBWFR LFE DSP |
| |||
DOLBY D | LS | S | RS | DGTL AUTO | VOL |
DTS | INPUT ATT | ||||
0dB : Normally select this.
Setting Auto Surround | Remote |
NOT |
Surround mode is automatically activated when a multichannel signal comes into this unit through the digital terminal.
You can enjoy Surround mode simply by selecting the source (with digital input selected for that source) — Auto Surround.
To activate Auto Surround, follow the procedure below.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
1Press SETTING.
SETTING | The CONTROL buttons now work for basic |
| settings. |
2Press CONTROL ° (or 5) repeatedly until “AUTO SR (Auto Surround)” (with the current setting)* appears on the display.
CONTROL
O LOGIC |
|
P |
|
TL AUTO |
|
UT ATT | VOL |
*“OFF” is the initial setting. If you have already changed the setting, “ON” will be shown.
3Press CONTROL 3 (or 2) to select “ON” (or “OFF”).
• Each time you press the button, Auto Surround turns “ON” or
“OFF.”
CONTROL |
|
|
|
| |
ANALOG | L | C | R | PRO LOGIC |
|
LPCM | SUBWFR LFE | DSP |
| ||
DOLBY D | LS | S | RS | DGTL AUTO | VOL |
DTS | INPUT ATT | ||||
18
