Basic operations
Basic operations
1 | 2 | 3 |
1 |
|
|
2 |
|
|
| When operating the receiver | |
| using the remote control, set | |
3 | the mode selector to |
|
| “AUDIO/TV/VCR/DBS.” |
| |
1 Turn on the power
Press 
STANDBY/ON (or 
AUDIO on the remote control).
The standby lamp goes off and the source lamp of the current source lights in red.
Current source name appears.
EQ C.TONE | VIRTUAL SB | AUDIO P. BASS | TA | NEWS | INFO | RDS | TUNED | ST | AUTO MUTING SLEEP AUTO MODE | |||
LPCM | L | C | R |
| PL |
|
|
|
|
|
| ATT |
DOLBY D | S . WFR LFE | NEO : 6 |
|
|
|
|
|
| HP | |||
DTS AAC |
|
| DSP 3D | MHz | |
LS SB RS | |||||
96 / 24 | AUTO SR | kHz | |||
To turn off the power (into standby)
Press 
STANDBY/ON (or 
AUDIO on the remote control) again.
The standby lamp lights in red.
NOTE
A small amount of power is consumed in standby mode. To turn the power off completely, unplug the AC power cord.
2 Select the source to play
On the front panel:
Turn SOURCE SELECTOR until the source name you want appears on the display.
The source lamp corresponding to the selected source lights in red.
•As you turn SOURCE SELECTOR, the source changes as follows:
EQ C.TONE | VIRTUAL SB AUDIO P. BASS | TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE | ||||||
LPCM | L | C | R |
| PL | ATT | ||
DOLBY D | S . WFR LFE | NEO : 6 | HP | |||||
DTS AAC |
|
|
|
|
| DSP 3D | MHz | |
LS | SB | RS | ||||||
96 / 24 | AUTO SR | kHz | ||||||
|
|
|
|
|
|
|
| |
DVR/DVD (DGT) 
VCR (DIGITAL) 
DBS (DIGITAL) 
TV (DIGITAL) 
FM 
AM 
(Back to the beginning)
DVR/DVD (DGT)*: Select the DVD recorder or DVD player.
VCR (DIGITAL)*: | Select the VCR. |
DBS (DIGITAL)*: Select the DBS tuner. | |
TV (DIGITAL)*: | Select the TV. |
FM: | Select an FM broadcast. |
AM: | Select an AM broadcast. |
From the remote control:
Press one of the source selecting buttons.
* Selecting the analog or digital input mode
For a component you have connected using both the analog connection and the digital connection methods (see pages 7 to 9), you need to select the correct input mode.
•You can select the digital input only for sources which you have selected digital input terminals for. (See “Setting the digital input (DIGITAL IN)
From the remote control ONLY:
Press SOUND, then press A/D INPUT to select the analog or digital input mode.
•Each time you press A/D INPUT, the input mode alternates between the analog input (“ANALOG”) and the digital input (“DGTL AUTO”).
DGTL AUTO: Select for the digital input mode. The receiver automatically detects the incoming signal format, then the digital signal format indicator (LPCM, DOLBY D, DTS, or DTS 96/24) for the detected signal lights up.
ANALOG: Select for the analog input mode.
Initial setting: ANALOG
NOTE
After pressing SOUND, the numeric buttons work for sound adjustments. To use the numeric buttons to operate your target source, press the corresponding source selecting button before operation; otherwise, the remote control may not work as you intend.
10
