JVC RX-E11S Operating procedure, Setting the speakers, Setting subwoofer information-SUBWOOFER

Basic settings

Operating procedure

On the front panel ONLY:

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

Ex.: When setting DIGITAL IN 1 terminal.

1Press SETTING.

MULTI JOG now works for the setting operation.

2Turn MULTI JOG until the item you want to set appears on the display.

•As you turn MULTI JOG, the setting items change as follows:

EQ C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE

LPCM	L	C	R	PL	ATT
DOLBY D	S .	WFR	LFE	NEO : 6	HP
DTS AAC				DSP 3D	MHz
	LS	SB	RS
96 / 24				AUTO SR	kHz

SUBWOOFER	FRONT SPK
CENTER SPK	SURRND SPK
DIST UNIT	FRNT L DIST
FRNT R DIST	CENTER DIST
SURR L DIST	SURR R DIST
SUBWFR OUT	VIRTUAL SB
DUAL MONO	CROSS OVER
LFE ATT	MIDNIGHT M.
DIGITAL IN1	DIGITAL IN2
DIGITAL IN3	AUTO SURRND
(Back to the beginning)

3Press SET.

The current setting of the selected item appears.

EQ C.TONE		VIRTUAL SB AUDIO P. BASS			TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE
LPCM	L	C	R	PL	ATT
DOLBY D	S . WFR LFE			NEO : 6	HP
DTS AAC				DSP 3D	MHz
	LS	SB	RS
96 / 24				AUTO SR	kHz

4Turn MULTI JOG to select the appropriate setting.

EQ C.TONE		VIRTUAL SB AUDIO P. BASS			TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE
LPCM	L	C	R	PL	ATT
DOLBY D	S . WFR LFE			NEO : 6	HP
DTS AAC				DSP 3D	MHz
	LS	SB	RS
96 / 24				AUTO SR	kHz

DVR/DVD DBS

TV VCR

Your setting is stored.

5Press SET.

6Repeat steps 2 to 5 to set other items if necessary.

Setting the speakers

Setting subwoofer information—SUBWOOFER

Each time the receiver turns on, the receiver detects the subwoofer connection and automatically changes the setting of the subwoofer.

When you want to change the setting manually, select either one below.

SUBWFR : YES Select when you have connected a subwoofer. The subwoofer indicator ( S . WFR) lights up on the display. You can adjust the subwoofer output level (see page 21).

SUBWFR : NO Select when you have disconnected a subwoofer.

Selecting this changes the front speaker size to “LRG” (see below).

NOTE

You need to change the setting each time you turn on the receiver if you want to change the subwoofer information set automatically.

Setting the speaker size—FRONT SPK (front speakers), CENTER SPK (center speaker), SURRND SPK (surround speakers)

Register the sizes of all the connected speakers.

LRG (large)	Select when the cone speaker size is larger than
	12 cm.
SML (small)	Select when the cone speaker size is smaller than
	12 cm.
NO	Select when you have disconnected a speaker.
	(Not selectable for the front speakers.)

Initial setting: LRG (for the front speakers)

SML (for the center and surround speakers)

NOTES

•If you have selected “SML (small)” for the front speaker size, you cannot select “LRG (large)” for the center and surround speaker sizes.

•When “SUBWOOFER” is set to “SUBWFR : NO,” the front speaker size is fixed to “LRG” (and you cannot select “SML”).

•If you change the center and/or surround speaker size either from “NO” to “SML” or “LRG,” or from “SML” or “LRG” to “NO,” the distance and output level set manually will be applied instead of those set by using Smart Surround Setup.

16