JVC RX-F10S manual Turning off the sounds temporarily, Changing the display brightness

Turning off the sounds temporarily

From the remote control ONLY:

Press MUTING to turn off the sound through all connected speakers and headphones.

“MUTING” appears on the display and the volume turns off.

EQ C.TONE		VIRTUAL SB AUDIO P. BASS			TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE
LPCM	L	C	R	PL	ATT
DOLBY D	S . WFR LFE			NEO : 6	HP
DTS AAC				DSP 3D	MHz
	LS	SB	RS
96 / 24				AUTO SR	kHz

To restore the sound, press MUTING again.

•Pressing VOLUME +/– (or turning MASTER VOLUME control on the front panel) also restores the sound.

Changing the display brightness

You can dim the display—Dimmer.

From the remote control ONLY:

Press DIMMER repeatedly.

•Each time you press the button, the display brightness changes as follows:

DIMMER 1: Dims the display slightly.

Dims the blue illumination slightly.

DIMMER 2: Dims the display more than DIMMER 1. Dims the blue illumination slightly (same as DIMMER 1).

DIMMER 3: Turns off the display and blue illumination. (Temporarily canceled when you operate the receiver.*)

DIMMER OFF: Cancels the Dimmer (normal display).

* Except when activating or deactivating TV Direct.

Turning off the power with the Sleep Timer

You can fall asleep while listening to music—Sleep Timer.

From the remote control ONLY:

Press SLEEP repeatedly.

•Each time you press the button, the shut-off time changes in 10 minute intervals. The SLEEP indicator lights up on the display.

					SLEEP indicator
EQ C.TONE		VIRTUAL SB AUDIO P. BASS			TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE
LPCM	L	C	R	PL		ATT
DOLBY D	S . WFR LFE			NEO : 6		HP
DTS AAC				DSP 3D		MHz
	LS	SB	RS
96 / 24				AUTO SR		kHz

10 20 30 40 50 60

OFF (canceled) 90 80 70

When the shut-off time comes:

The receiver turns off automatically.

To check or change the remaining time until the shut-off time:

Press SLEEP once.

The remaining time (in minutes) until the shut-off time appears.

• To change the shut-off time, press SLEEP repeatedly.

To cancel the Sleep Timer:

Press SLEEP repeatedly so that “SLEEP OFF” appears on the display. (The SLEEP indicator goes off.)

•The Sleep Timer is also canceled when:

–You turn off the receiver, or

–You activate TV Direct.

Basic adjustment of auto memory

This receiver memorizes sound settings for each source:

•when you turn off the power, and

•when you change the source.

When you change the source, the memorized settings for the newly selected source are automatically recalled.

The following can be stored for each source:

•Analog/digital input mode (see page 12)

•Subwoofer audio position (see page 14)

•Speaker output level (see page 23)

•Subwoofer phase (see page 24)

•Digital equalization pattern (see page 24)

•Bass boost (see page 24)

•Input attenuator mode (see page 24)

•Surround/DSP mode selection (see pages 30 and 31)

NOTE

If the source is FM or AM, you can assign a different setting for each band.

Signal and speaker indicators on the display

Signal indicatorsSpeaker indicators

L

C R

L

C

R

S . WFR LFE

EQ C.TONE

VIRTUAL SB AUDIO P. BASS

TA NEWS

INFO RDS

LPCM

L

C R

PL

S . WFR LFE

DOLBY D

NEO : 6

S .

WFR

LFE

LS

SB RS

LS SB

RS

DTS

AAC

DSP 3D

LS SB RS

96 /

24

AUTO SR

The signal indicators light up as follows:

L:• When digital input is selected: Lights up when the left channel signal comes in.

•When analog input is selected: Always lights up.

R:• When digital input is selected: Lights up when the right channel signal comes in.

•When analog input is selected: Always lights up.

C:Lights up when the center channel signal comes in. LS*: Lights up when the left surround channel signal comes

in.

RS*: Lights up when the right surround channel signal comes in.

SB: Lights up when the surround back channel signal comes in.

LFE: Lights up when the LFE channel signal comes in.

* When monaural surround signal comes in, only “S” lights up.

NOTE

When “DVD MULTI” is selected as the source, all the signal indicators except “SB” light up.

The speaker indicators light up as follows:

•The subwoofer indicator (S . WFR) lights up when “SUBWOOFER” is set to “SUBWFR :YES.” For details, see page 18.

•The other speaker indicators light up only when the corresponding speaker is set to “SML (small)” or “LRG (large),” and also when required for the current playback.

Basic operations

15