JVC RX-F10S manual Troubleshooting, English

Models: RX-F10S

1 88
Download 88 pages 54.49 Kb
Page 86
Image 86
Manual background

Troubleshooting

English

Use this chart to help you solve daily operational problems. If there are any problems you cannot solve, contact your JVC’s service center.

 

 

PROBLEM

POSSIBLE CAUSE

 

SOLUTION

 

 

The power does not come on.

The power cord is not plugged in.

Plug the power cord into an AC outlet.

 

 

 

 

 

 

 

 

 

 

The receiver turns off (enters standby

Speakers are overloaded because of high

1.

Stop the playback source.

 

 

mode).

volume.

2.

Turn on the receiver again, then turn the

 

 

 

 

 

volume down.

Power

 

 

 

 

 

 

 

Speakers are overloaded because of a

Check the speaker wiring. If speaker wiring

 

 

 

 

 

 

short circuit at the speaker terminals.

is not short-circuited, contact your dealer.

 

 

 

 

 

 

 

 

The receiver is overloaded because of a

Consult your dealer after unplugging the

 

 

 

high voltage.

power cord.

 

 

 

 

 

 

 

“OVER HEAT” flashes on the display,

The receiver is overloaded because of high

Turn on the receiver again. If the receiver

 

 

then the receiver turns off.

volume or long time usage.

turns off soon, consult your dealer after

 

 

 

 

unplugging the power cord.

 

 

 

 

 

 

 

 

No sound from speakers.

Speaker signal cables are not connected.

Check speaker wiring, then reconnect if

 

 

 

 

 

necessary (see page 6) after unplugging

 

 

 

 

the power cord.

 

 

 

 

 

 

 

 

Connections are incorrect.

Check the audio connections (see pages 7

 

 

 

 

to 11) after unplugging the power cord.

 

 

 

 

 

 

 

 

An incorrect source is selected.

Select the correct source.

 

 

 

 

 

 

 

 

Muting is activated.

Press MUTING to cancel the mute (see

 

 

 

 

page 15).

 

 

 

 

 

 

 

 

An incorrect input mode (analog or digital)

Select the correct input mode (analog or

Sound

 

 

is selected.

digital).

 

 

 

 

 

 

 

TV Direct is activated.

Deactivate TV Direct (see page 14).

 

 

 

 

 

 

 

 

 

 

Sound from one speaker only.

Speaker signal cables are not connected

Check speaker wiring and reconnect if

 

 

 

properly.

necessary (see page 6) after unplugging

 

 

 

 

the power cord.

 

 

 

 

 

 

 

Bass sound is reinforced too much

Appropriate bass level is not selected.

Adjust audio position level (see page 14).

 

 

when listening in stereo.

 

 

 

 

 

 

 

 

 

 

Sounds are intermittently distorted by

When you use the digital coaxial connection,

This is not a malfunction.

 

 

the outside noise such as a lightning

the sounds may be intermittently distorted

 

 

 

 

discharge.

by the outside noise such as a lightning

 

 

 

 

 

discharge but the sound will be restored

 

 

 

 

 

automatically.

 

 

 

 

 

 

 

 

 

 

Remote control does not operate as

The remote control is not ready for your

Set the mode selector correctly, then press

 

 

 

you intend.

intended operation.

the corresponding source selecting button

control

 

 

 

or SOUND before operation.

 

 

 

 

 

 

Remote control does not work.

sensor on the receiver.

Remove the obstruction.

 

 

There is an obstruction hiding the remote

Remote

 

 

 

 

 

 

The mode selector is set to the incorrect

Set the mode selector to the proper

 

 

 

Batteries are weak.

Replace batteries.

 

 

 

position.

position.

 

 

 

 

 

 

 

Buttons cannot be used.

TV Direct is activated.

Deactivate TV Direct (see page 14).

 

 

 

 

 

 

 

 

Continuous hiss or buzzing during FM

Incoming signal is too weak.

Connect an outdoor FM antenna or contact

 

 

 

 

reception.

 

your dealer.

 

 

 

 

 

 

 

 

The station is too far away.

Select another station.

Tuner

 

 

 

 

 

 

 

The wrong antenna is being used.

Check with your dealer to be sure you have

 

 

 

 

 

 

 

the correct antenna.

 

 

 

 

 

 

 

 

Antennas are not connected properly.

Check the connections.

 

 

 

 

 

 

 

Occasional cracking noise during FM

Ignition noise from automobiles.

Move the antenna farther from automobile

 

 

reception.

 

traffic.

 

 

 

 

 

 

Troubleshooting

39

Page 86
Image 86
JVC RX-F10S manual Troubleshooting, English