![](/images/new-backgrounds/1232892/23289215x1.webp)
CONNECTION/INSTALLATION
Procedures
Execute connection/installation according to the procedures described below.
Mounting the lens
Mount the lens according to the procedures described below.
Turn OFF the power supply to all equipment to be used before making carefully.
4.Setting the switches | 6.Back focus adjustment |
( Page 13) | ( Page 21) |
| SET |
|
|
| CAMERA |
|
|
| SETUP | EXT | ON |
|
| ||
MENU |
| INT/GL | LL |
|
| DUPLEX | SIMPLEX |
|
| RX | ON |
|
| IOT USED |
|
|
|
| VIDEO |
|
|
| DC |
(b)F
1. Before mounting a lens, check whether it is a
To change the mounting method, loosen the
As regards the dimension (b) of the area to which the lens is to be installed as illustrated on the left diagram, use the one with less value than what’s shown in the table below.
For both the
7.Auto white balance control adjustment ( Page 22)
5.Lens adjustment ( Page 20)
3.Mounting the camera 1.Mounting the lens
( Page 18) | ( Page 15) |
To controlling systems such as
(c)
3.
VIDEO
DC
2. |
4. |
never use whatever exceeds the dimen- sion (b), as such will not allow normal installation and damage the inner part of the camera, resulting in a malfunc- tion.
Lens | Flange back (c) | Dimension (b) |
|
|
|
C mount lens | 17.526mm | 5.5mm or less |
|
|
|
CS mount lens | 12.5mm | 5.5mm or less |
|
|
|
The F mark indicates a focal point.
DC 12V/AC 24V power supply
1 | 3 |
2. Mount the lens on the camera by turning the lens clockwise. Adjust its position.
2.Connections ( Page 16)
Genlock sync signal generator
| + | - |
|
|
|
|
|
|
| 1 | 2 | ISOLATED POWER ONLY |
|
|
|
|
|
DC12V | AC24V | CLASS 2 ONLY(U TYPE) | (E TYPE) | TX+ TX- RX+ RX- AUX GND | ||||
|
|
|
|
| A | B | C | D |
| Y/C OUT |
SYNC IN | VIDEO OUT |
| SEE INST- |
POWER | RUCTION |
MANUAL |
To alarm terminals such as switches
Monitor
2 | 4 |
| CAUTION: |
3 | Always attach the fer- |
1 | rite core (supplied) to |
| |
4 | the lens cable. |
2 | ( Page 16) |
Attached 4 pin plugs
3. When using an
4. If the lens has an
If the lens cable has a different type of plug, use the
This is the connected example of the
Lens | DC IRIS | VIDEO IRIS | 1 | 3 | ||||||||
Pin No. | (does not contain EE amplifier) | (contain EE amplifier) | ||||||||||
|
|
|
|
|
|
|
| |||||
1 | Brake | – | 9V [max 50mA] |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |||||
2 | Brake | + | NC |
|
|
|
|
|
|
|
| |
3 | Drive | + | VIDEO |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |||||
4 | Drive | – | GND | 2 | 4 |
|
|
| ||
|
|