JVC TM-2001U operating instructions Troubleshooting, Cable/Satellite Search Codes Function

22

Troubleshooting

PROBLEMS	CHECK
There is no power	• See if the power cord became unplugged.
	• Check for a blown fuse or circuit breaker or a power outage.
There is no picture	• The antenna could be disconnected.
or sound	• The input mode could be set improperly. See page 40.
	• The tuner (Auto Tuner Setup) could be set improperly. See page 20.
	• The TV station may be having difficulties. Check to see if other stations are working.
Remote control is not	• Check to see that the batteries are still working and properly installed.
operating properly or	• Make sure the remote has a clear sight path to the TV.
at all	• Check that the TV/CATV switch is in the proper position.
You cannot select a	• You may be too far from the TV. You must be within 23 feet (7 meters).
certain channel	• Make sure the channels have been programmed. See "Channel Summary", page 21.
	• Check to see if the channel is locked. See "Channel Summary - Lock" page 21.
The power turns off	• Make sure the set did not become unplugged.
by itself	• Perhaps the On/Off Timer is set. See page 36.
	• Check to see if the Sleep Timer was set. See page 39.
The clock is wrong	• The power was interrupted and the clock was not reset. See page 34.
The On Timer is	• There is a problem with the TV. Unplug the set and call for service.
blinking
The color quality	• Tint and Color may be improperly adjusted. See page 30.
is poor	• The Video Status mode may be turned to the wrong setting. See page 31.
There are lines	• There could be interference from another electrical appliance, such as a computer,
across the picture	another TV or VCR. Move any such appliances further away from the TV.
The picture is spotted	• There could be interference from a high-wattage appliance, like a hairdryer or vacuum,
	operating nearby. Move the antenna away from the appliance or change to a coaxial
	cable connection which is less prone to interference.
There are double	• A building or passing airplane can reflect the original signal and produce a second,
pictures (ghosts)	slightly delayed one. Adjust your antenna position.
Picture is snowy	• Your antenna may be damaged, disconnected or turned. Check the antenna
(image noise)	connection. If the antenna is damaged, replace it.
Screen is 80% black	• The Closed Caption Text mode is on. Turn it off in the Closed Caption Menu, page 37.
Stereo or bilingual	• Make sure the MTS settings are correct. See "MTS" on page 33.
programs can't be
heard
There is no sound	• The TV Speaker option may be turned off. See page 33.
from the TV's speakers
Static electricity	• It is normal to feel static electricity if you brush or touch the screen.
You hear occasional	• It is normal for the TV to make crackling sounds when first turned on or off. Unless
crackling sounds	the sound or picture become abnormal, this is fine.
The picture is	• Make sure the BNC connector box is properly connrcted to the TV.
excessively bright	• The television Video input jack(RCA) is not terminated.

Search Codes

Cable/Satellite Search Codes Function:

1)Slide the 2-Way Mode Selector switch to CATV.

2)Press the TV POWER and RETURN+ buttons. Hold for at least three seconds and release.

3)Press TV POWER, see if the CATV or Satellite box responds.

4)If there was a response, press RETURN+. The operating codes are now set. If there was no response, repeat Step 3. If you repeat Step 3 a total of 52 times without a response, use the remote control which came with the equipment.

5)Press RETURN+ to exit.

VCR Search Codes Function:

1)Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “VCR”.

2)Press the VCR POWER and RETURN+ buttons. Hold for at least three seconds and release.

3)Press VCR POWER, see if the VCR responds.

4)If there was a response, press RETURN+. The operating codes are now set. If there was no response, repeat Step 3. If you repeat Step 3 a total of 80 times without a response, use the manufacturers remote control which came with the VCR.

5)Press RETURN+ to exit.

DVD Player Search Codes Function:

1)Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “DVD”.

2)Press the DVD POWER and RETURN+ buttons. Hold for at least three seconds and release.

3)Press DVD POWER, see if the DVD player responds.

4)If there was a response, press RETURN+. The operating codes are now set. If there was no response, repeat Step 3. If you repeat Step 3 a total of 30 times without a response, use the manufacturers remote control which came with the DVD player.

5)Press RETURN+ to exit.

TM-2701SU TM-2001U

42 43