Manuals / JVC / Household Appliance / Home Security System

JVC VN-C10 Preparations Connection and Installation, 1-2Connecting the Power Cord, Cable to Use

Models: VN-C10

1 78

Download 78 pages 63.99 Kb

Page 14

Preparations (Step 1 Connection and Installation)

Preparations (Step 1 Connection and Installation)

1-2 Connecting the Power Cord

Connect the camera to DC 12 V or AC 24 V.

The power indicator is lit when the power is turned on.

To

Power

	1	2	ISOLATED POWER ONLY			G	2	1	OUT COM
DC12V	AC24V	CLASS 2 ONLY ForUSA	ISOLATED POWER ONLY	For EUROPE	INPUT				OUTPUT

ALARM

			PUSH
	Power
	indicator	POWER	10BASE-T/100BASE-TX
	lamp	POWER	10BASE-T/100BASE-TX
	lamp		DO NOT CONNECT TO THE
			DO NOT CONNECT TO THE
			TELEPHONE NETWORK
			For USA

Power Cord

¥Do not connect the power cord to DC 12 V and AC 24 V at the same time.

¥Use a lug plate to securely connect the power cord to the power terminals and avoid misconnection or loose connection.

¥For DC 12 V connection, ensure that the polarities, positive and negative, are correctly oriented.

¥For DC 12 V connection, the ripple voltage should not exceed 50 mV.

Cable to Use

¥Length: 30 m maximum

¥UL1007, UL1015 or equivalent

¥AWG #20 or equivalent, or higher

WARNING

Connect with the appropriate power-supply voltage.The rated voltage for VN-C10 is DC 12 V or AC 24 V, 50 Hz/60 Hz. If a voltage exceeding the rating is supplied, malfunction, or in the worst case, fuming or fire, may be caused.

For AC 24 V, ensure that the primary side is insulated with the secondary one.

For a system with multiple VN-C10s

In a system where more than one VN-C10 are used, turn on the power for a VN-C10 first and proceed the setting to 2-4 Other Settings with V.Networks Setup Tool. Only then turn on the power for a second one and go on to 2-4. Repeat the procedure for the other cameras.

Note

The IP address of VN-C10 is set to Ò198.168.0.2Ó at the factory. Proper access cannot be established due to IP address redundancy if the power is turned on for multiple cameras at one time under a single LAN environment. Do not turn on the power for multiple cameras at the same time. If an IP address redundancy occurred, ensure that only one VN-C10 exists on a single LAN environment and wait for some time (at least 10 minutes). Or turn off the power once for all network equipment and turn it on again for proper access to VN-C10.

14

Image 14

JVC VN-C10 Preparations Connection and Installation, 1-2Connecting the Power Cord, Connect the camera to DC 12 V or AC

Contents

INSTRUCTIONS V.NETWORKSModel VN-C10 For Customer UseIMPORTANT SAFEGUARDS Information for USA Safety PrecautionsFOR USA AND CANADA AVERTISSEMENTContents Introduction Preparations Specifications Step 4 Setting with V.Networks ControllerTroubleshooting External DimensionsCharacters and Symbols used in this Manual FeaturesHow to Use This Manual IntroductionUpgrading the Application Required Operating Environment PC SpecificationsLAN Specifications Introduction Operating Precautions Front, top and side views Controls, Connectors and Indicators2Back-focusadjustment ring 1Lens mount@POWER indicator Controls, Connectors and Indicators continued0RESET button #DC 12 V/AC 24 V Power terminalNetwork Connection PreparationsConnection Examples LAN Connection Peer-to-PeerConnectionStep 1 Connection and Installation Preparation ProcedureSet the camera in the following procedure Step 2 Setting the Network1-1Attaching a Lens Preparations Step 1 Connection and InstallationAttach a lens in the following procedure 4-PinPlugPower Cord Preparations Step 1 Connection and Installation1-2Connecting the Power Cord Connect the camera to DC 12 V or AC¥For PC connection Use a cross-overcable 1-3Connecting a LAN Cable¥For hub connection Use a straight cable ALARMCable Specifications 1-4Connecting the Alarm I/O TerminalsAlarm Input Terminal Input RequirementsOutput Requirements Alarm Output Terminal1-4Connecting the Alarm I/O Terminals continued Fall Prevention 1-5Installing the Camera Fall-PreventivewireSecuring wire Preparations Step 1 Connection and Installationthe camera in the following procedure Preparations Step 2 Setting the Network2-1Installing the Software Installing V.Networks ControllerPreparations Step 2 Setting the Network 2-2Setting the PC’s IP Address for Windows XP5. Click in Local Area Connection Properties 2-2Setting the PC’s IP Address for Windows Preparations Step 2 Setting the NetworkSelect Use the following IP Address 4. Click IP Address in TCP/IP properties5. Click Set the IP address to Ò192.168.0.3.ÓPreparations Step 2 Setting the Network 4. Start up V.Networks Controller. Page 2. Confirm the settings3. Click Page 27 Page Page 39 Page Page Page 41 Page Page 2-4Other Settings with V.Networks Setup ToolPreparations Step 2 Setting the Network Page 30 Page 32 PageAccess Right Level Operation when alarm input is activated This section describes alarm settingAlarm input is activated in the following cases Preparations Step 2 Setting the Network4Relay Alarm 1 Alarm2 Alarm 6Alarm force outputPreparations Step 2 Setting the Network 2. Select Motion Detect of V.Networks Setup ToolThis function cannot be set for MPEG4 Available MASK Refresh IntervalMotion Distinction Interval Reference ImagePreparations Step 2 Setting the Network Trigger Recording2. Frame Rate Recording files 3. OthersRecording time Saving images of local recording to the PCThis function cannot be set for MPEG4 Preparations Step 2 Setting the NetworkTransfer error 3Password8Error Recovery Connection error 1FTPPreparations Step 2 Setting the Network Multicast cannot be set for MPEG4Multicast 3. The Multi Address Search screen is displayed 1. Start up V.Networks Setup Tool. Select Search2. The V.Networks Search screen is displayed 4. The search result is displayedMemory capacity can be checked Preparations Step 2 Setting the Network1. Start up V.Networks Setup Tool and select Web Preparations Step 2 Setting the Network NTP is used 1. Start up V.Networks Setup Tool and select TimeNTP is not used 2. New is displayed Preparations Step 2 Setting the NetworkFor a fixed-focuslens Preparations Step 3 Adjusting the Camera3-1 Back-focusAdjustment For a zoom lens4-1Starting Up V.Networks Controller 1 File 4-2Function Settings with V.Networks Controller3 Setting 2 View4-3Motion Detection Standby 4-4Image Size and Inversion 1. Select View4-5Setting the Image Quality 1Compression Rate 4-5Setting the Image Quality continued6Default 2White Balance4-6Frame Rate 3. When the settings are complete, click 4-7Alarm Setting1. Select Setting and Alarm Setting Relay Alarm 4-7Alarm Setting continued 1MessageAlarm Operation 2Recording4-8Time Stamp Select Setting and Time StampProceed with the setting 3. When complete, click 1. Select Setting and Property2. Proceed with the setting 4-9Changing the Registered Information1Camera 5-1Operations with V.Networks ControllerReduced screen 2PLAY5-2Record/Stop 5-3Playback 1. Click the PLAY buttonSlidebar 5-3Playback continued 3. Click4. Playback is displayed ¥ Can be dragged with the mouseApproximate recording time for 2 GB MPEG4 data 5-4Other Instructions on Record and PlaybackRecord/Playback time 5-5Snapshot Operations Step 6 Operations with a Web Browser 6-1Required Operating EnvironmentOperations Step 6 Operations with a Web Browser 6-2Access AuthorizationVerifying access authorization Security level2. The VN-C10top page appears 6-3Starting Up the Web Browser1. Start up the Web browser Top page 6-4Settings with a Web BrowserThe setting page is displayed Operations Step 6 Operations with a Web Browser6-4Settings with a Web Browser 1. Other Settings Other SettingsAdministrator Level Default GatewayPassword administrater passwordAdjust Interval Default Page continuedNTP Settings Available/ Not availableCompression Rate 6-4Settings with a Web Browser 2. Image SettingsImage Quality Setting Window SaturationImage size 6-4Settings with a Web Browser 3. View SettingsView Setting Window EffectAlarm In 6-4Settings with a Web Browser 4. Alarm SettingsAlarm Setting Window Alarm 1 and6-4Settings with a Web Browser 5. FTP Settings FTP Client Setting WindowOn connect error when the next image is uploadedError Recovery On transfer error6-5Viewing Still Images Still Image PageOperations Step 6 Operations with a Web Browser 6-6Viewing Moving ImagesMoving Image Page Displaying a Still Image 6-7 VN-C10Image LinkDisplay in Java Applet Displaying a Moving ImageOthers TroubleshootingSymptoms Remedial ActionsUnit mm Others SpecificationsExternal Dimensions VICTOR COMPANY OF JAPAN, LIMITED VN-C10V.NETWORKS2003 VICTOR COMPANY OF JAPAN, LIMITED