Preparations
CConnecting to a TV with component jacks
You can enjoy picture of
NOTES
•Connect “Y” to “Y,” “PB” to “PB” (CB), “PR” to “PR” (CR) correctly.
•When using the COMPONENT VIDEO OUT jacks, do not connect the
•If your TV has component video input jacks of BNC type, use an adapter which converts a pin jack to a BNC jack (not supplied).
Progressive scan video playback available
In the Progressive scanning mode, you can enjoy high quality picture with less flickers when the COMPONENT VIDEO OUT jacks are connected to a TV or monitor that supports the progressive video input.
About the scanning mode
Depending on the material source format, DVD VIDEO discs can be classified into two types; film source and video source (note that some DVD VIDEO discs contain both film source and video source). Film sources are recorded as
When the unit plays back a film source material, uninterlaced progressive output signals are created using the original information. When a video source material is played back, the unit interleaves lines between the interlaced lines on each to create the interpolated picture and outputs as the progressive signal.
Preparations
TV |
|
|
| Red |
| IN |
| PR | |
|
| PB | Blue | |
|
|
| ||
|
|
| Y | |
| C | The unit | ||
|
|
|
| |
VIDEO |
| White |
| |
|
|
|
| |
LE | FT |
|
|
|
AUD | IO |
|
| Green |
|
|
|
| |
RIG | HT |
|
|
|
|
|
|
|
NTSC/PAL selector | Red | |
See page 6. | ||
|
| COM | PU | LINK |
AV |
|
| |
|
|
|
| 525p | ||||
525i |
|
|
|
| REMOTE |
|
|
|
| ||
|
|
|
|
|
|
AL | OU | T |
| AM | |
DIGIT |
| |
STRE | L |
COAX | IAL |
|
|
|
|
| VIDEO | OU | T |
| NTSC | PA | L | White | |
|
| T | VI | DEO |
|
|
| 525p | TE |
|
|
|
| OU | EO |
|
| REMO |
|
|
| ||||
| LEFT |
|
| 525i |
|
|
|
|
| |||
RIG | HT |
|
|
|
|
|
|
|
|
|
|
|
|
|
| Red |
|
| PB | ENT |
Y | COM |
| |
| Red | ||
|
|
|
Green
Blue
Audio cable (not supplied)
Component video cable (not supplied)
Selecting the 525i/525p/REMOTE selector position
•If your TV equipped with component jacks does not support the progressive scanning mode
Set the 525i/525p/REMOTE selector to “525i.”
•If your TV equipped with component jacks supports the progressive scanning mode
Set the 525i/525p/REMOTE selector to “525p.”
•If you want to select the scanning mode between the interlace and progressive modes (depending on the source condition, or when connecting more than one television, etc.)
Set the 525i/525p/REMOTE selector to “REMOTE.”
Thus you can select the mode from the remote control unit.
NOTE
You must change the 525i/525p/REMOTE selector position while the unit power is off. Otherwise, the changed setting is not effective.
Activating the Progressive scanning mode using the remote control unit
When the unit is turned on and the 525i/525p/REMOTE selector is set to “REMOTE,” press and hold down VFP - PROGRESSIVE SCAN for a few seconds.
The scanning mode switches between the Progressive scanning and Interlaced scanning modes.
When the scanning mode is set to the Progressive mode, the PROGRESSIVE indicator on the front panel turns on. Depending on the [PICTURE SOURCE] setting on the [PICTURE] preference display and whether the current DVD VIDEO disc is
indicator differs, as shown in the table below.
Setting of | Source type of DVD VIDEO | |
|
| |
[PICTURE SOURCE] | Film source | Video source |
| ||
|
|
|
AUTO | Green | Red |
|
|
|
FILM | Green | Green |
|
|
|
VIDEO (NORMAL)/ | Red | Red |
(ACTIVE) |
|
|
|
|
|
*While stopped in the Progressive scanning mode, the PROGRESSIVE indicator is lit in red regardless of the [PICTURE SOURCE] selection.
NOTES
•The Progressive scanning mode works only when you connect the unit’s COMPONENT VIDEO OUT jacks to your TV.
•The Progressive scanning mode works only when the signal format is NTSC.
•There are some progressive TV and
•All JVC progressive TV and
•The VIDEO jack,
4