Installation Instructions (cont'd)

Venting (cont'd)

All vent gases must be completdy vented to the outdoors of the

structure (dwelling). InstaU only the draft hood provided with the new water heater and no other draft hood.

Vent pipes must be secured at each joint with sheet metal screws.

TO

CHIMNEY

VENT PIPE INSTALLATION

There must be a minimfim of 6" clearance between single wall vent pipe and any combustible material. Fill and seal any clear- ance between single wall vent pipe and combustible material with mortar mix, cement, or other noncombustible substance. For other than single wall, follow vent pipe manufacturer's dear- ance specifications. To insure a tight fit of the vent pipe in a brick chimney, seal around the vent pipe with mortar mix

cement.

AWARNING

Failureto haverequired clearancesbetweenvent pipingand combustiblematerial will resultin afire hazard.

AWARNING[

Be sure vent pipe is properlyconnectedto preventescapeof

dangerousflue gaseswhichcoud causedeadlyasphyxation.

AWARNING

Chemical vapor corrosionof the flue and vent system may occurif air for combustioncontainscertain chemicalvapors. Spray can propellants,cleaningsolvents,refrigerator and air conditioner refrigerants, swimmingpool chemicals,calcium and sodiumchloride,waxes,bleach,and processchemicalsare typicalcompoundswhicharepotentially corrosive.

Gas Piping

AWARNING

Make sore the gas suppliedis the same type listed on the model rating plate. The inlet gas pressuremust not exceed 14 incheswater column ½ pound per squareinch(3.SkPa).

The minimum inlet gaspressurelisted on the model ratin plate isfor the purposeofinput adj_

AW.A.RNING[

If the gascontrolvalveis subjectedto pressuresexceeding ½ [ pound per square inch(3.SkPa),the damageto the gascon-[

[ trel valvecouldresultin a Ere or explosionfrom leakingga_

AWARNING[

If the main gasline shutoffservingall gasappliancesis used,[ alsoturn "OFF" the gasat eachappliance.Leaveall gasappli-

ancesshutoff untilthe water heater installationiscomplete.

A gas line of sufficient size must be run to the water heater. Consult the latest edition of National Fuel Gas Code ANSI

Z223.1, also referred to as NFPA54 and the gascompany concern- ing pipe size.

There must be:

•A readily accessible manual shut offvalve in the gas supply line serving the water heater, and

•A drip leg (sediment trap) ahead of the gas control valve to help prevent dirt and foreign materials from entering the gas control valve.

•A flexible gas connector or a ground joint union between the shutoffvalve and control valve to permit servicing of the unit.

Be sure to check all the gas piping for leaks before lighting the water heater. Use a soapy water solution, not a match or open flame. Rinse offsoapy solution and wipe dry.

Standard Models are for installation up to 3,300 feet above sea level.

High Altitude Models are for installation from 3,300 to 5,500 feet above sea level.

Ifa standard model is installed above 3,300 feet or a high altitude

model is installed above 5,500 feet, the input rating must be reduced at the rate of 4 percent for each 1,000 feet above sea level.

Contact your local Sears Service Center or gas utility for forther information.

AWARNING

The appliance and its gas connection must be leak tested beforeplacngthe appliancein operation.

14

Page 13 Page 15
Page 14
Image 14
Kenmore 153.330401 owner manual Gas Piping, Venting contd, Vent Pipe Installation
Page 13 Page 15

153.330401 specifications

The Kenmore 153.330401 is a highly regarded air conditioner that combines efficient cooling capabilities with user-friendly features, making it an ideal choice for homeowners seeking comfort during the heat of summer. This window-mounted air conditioning unit is designed to deliver powerful cooling while also minimizing energy consumption.

One of the standout features of the Kenmore 153.330401 is its impressive cooling capacity, measured at 10,000 BTU, which allows it to effectively cool spaces of up to approximately 450 square feet. This makes it suitable for medium to large rooms, such as living rooms, bedrooms, or even small office spaces. The air conditioner is equipped with multiple cooling settings, allowing users to tailor the cooling experience to their preferences.

The Kenmore 153.330401 also features an energy-saving mode that enhances its efficiency. This function helps to reduce electricity costs by automatically adjusting the cooling output based on the ambient temperature and the set preferences. The unit is ENERGY STAR certified, which ensures that it meets strict energy efficiency guidelines set by the Environmental Protection Agency.

Another notable technology integrated into the Kenmore 153.330401 is its quiet operation. This air conditioning unit is engineered to minimize noise during operation, ensuring a peaceful and comfortable environment, which is particularly valuable for bedrooms or quiet spaces. The unit also comes equipped with a remote control for added convenience, allowing users to adjust settings from across the room without having to get up.

The Kenmore 153.330401 includes adjustable air vents and a programmable timer, enabling users to set specific cooling schedules based on their daily routines. Additionally, the unit features a washable and reusable air filter, which helps to improve indoor air quality by trapping dust and allergens, and can be easily maintained for long-term performance.

In summary, the Kenmore 153.330401 air conditioner is a versatile and efficient cooling solution that offers robust performance, user-focused features, and energy-saving technologies. Whether for a living room, bedroom, or home office, this air conditioner provides a reliable option for maintaining a comfortable indoor environment during the hottest months of the year. Its combination of power, efficiency, and convenience makes it an excellent choice for any household.
Top Page Image Contents