This water heater shall not be connected to any heating systems or component(s) used with a non-potable water heating appliance.

All piping components connected to this unit for space heating applications shall be suitable for use with potable water.

Toxic chemicals, such as those used for boiler treatment shall not be introduced into this system.

Water supply systems may, because of such events as high line pressure, frequent cut-offs or the effects of water hammer, have installed devices such as pressure reducing valves, check valves, back flow preventers, etc. to control these types of problems. When these devices are not equipped with an internal by-pass, and no other measures are taken, the devices cause the water system to be closed. As water is heated, it expands (thermal expansion) and closed systems do not allow for the expansion of heated water.

The water within the water heater tank expands as it is heated and increases the pressure of the water system. If the relieving point of the water heater's temperature-pressure relief valve is reached, the valve will relieve the excess pressure. The

temperature-pressure relief valve is not intended for the constant relief of thermal expansion. This is an unacceptable condition and must be corrected. It is recommended that any devices installed which could create a closed system have a by-pass and/or the system have an expansion tank to relieve the pressure built by thermal expansion in the water system. Refer to the Thermal Expansion section under Troubleshooting Guide or contact local plumbing authority or local Sears Service Center on how to control this situation.

NOTE: To protect against untimely corrosion of hot and cold water fittings, it is strongly recommended that di-electric unions or couplings be installed on this water heater when connected to copper pipe.

Property Damage Hazard

Avoid water heater damage.

Install thermal expansion tank if necessary.

Do not apply heat to cold water inlet.

Contact qualified installer or Sears Service Center.

Figure 15 shows the typical attachment of the water piping to the water heater. The water heater is equipped with 314" NPT water connections.

NOTE: If using copper tubing, solder tubing to an adapter

before attaching the adapter to the cold water inlet connection. Do not solder the cold water supply line directly to the cold water inlet. It will harm the dip tube and damage the tank.

Look at the top cover of the water heater. The water outlet is marked "HOT". Put two or three turns of Teflon tape around the threaded end of the threaded-to-sweat coupling and around both ends of the 3/4" NPT threaded nipple. Using flexible connectors, connect the hot water pipe to the hot water outlet on the water heater.

TEFLON® is a registered trademark of E.I. Du Pont De Nemours and Company.

Look at the top of the water heater. The cold water inlet is marked "COLD". Put two or three turns of Teflon tape around the threaded end of the threaded-to-sweat coupling and around both ends of the 3/4" NPT threaded nipple. Using flexible connectors, connect the cold water pipe to the cold water inlet of the water heater.

NOTE: This water heater is super insulated to minimize heat loss from the tank. Further reduction in heat loss

can be accomplished by insulating the hot water lines from the water heater.

INSTALLATION

COMPLETED

USING

 

INSTALLATION

KIT

 

 

FLEXIBLE

 

 

 

 

WATER

 

SHUTOFF

 

CONNECTORS

 

VALVE

 

HOT WATER

 

 

_

COLD WATER

OUTLET

 

 

_

INLET

THREADED TO

 

THREADED

TO

 

SWEAT COUPLING

SWEAT COUPLING

 

3/4"THREADED-

3/4"THREADED

 

 

COUPLING

 

COUPLING

 

 

DRAFTHOOD

 

 

 

 

 

 

TEMPERATURE-

 

 

 

PRESSURE

 

 

 

RELIEF

VALVE

 

(Do not cap or plug)

6" MAXIMUM

AIR GAP

FLOOR DRAIN

T & P Valve and Pipe Insulation

Remove insulation for T & P valve and pipe connections from carton.

PIPE

INSULATION FLUE PIPE

ULTO

FIGURE 15A.

Fit pipe insulation over the incoming cold water line and the hot

water line. Make sure that the insulation is against the top cover of the heater.

13

Page 13
Image 13
Kenmore 153.33062, 153.330652, 153.330632, 153.330642 owner manual Property Damage Hazard, Installation Completed Using KIT

153.330642, 153.33062, 153.330632, 153.330652 specifications

The Kenmore model series 153.330632, 153.330652, 153.33062, and 153.330642 represent a versatile lineup of washing machines designed to cater to a variety of laundry needs. Each model comes equipped with unique features and technologies aimed at enhancing the user's washing experience while ensuring reliability and performance.

One of the standout features across these models is their efficient water usage. Designed with modern technology, these machines incorporate advanced sensors that adjust the water level according to the load size. This not only conserves water but also contributes to lower utility bills, making them environmentally friendly options.

In terms of operation, the Kenmore models boast a range of wash cycles tailored to different fabric types and soil levels. From delicate items to heavy-duty fabrics, users can choose the appropriate cycle to ensure optimal cleaning without damaging their garments. The presence of a quick wash option is also a highlight, enabling users to clean lightly soiled items in a fraction of the time.

The Kenmore series is also designed for user convenience. Features such as a digital display control panel allow for intuitive operation. Users can easily select their desired settings and monitor the wash cycle progress. Additionally, the machines are equipped with a delay start function, which provides flexibility for users to schedule their laundry according to their convenience.

Another notable characteristic of these models is the installation of noise-reducing technologies. This minimizes operational sounds, allowing for quieter washing cycles, which is particularly beneficial for households with infants or those who prefer a tranquil environment.

Durability is a significant aspect of the Kenmore brand. Each machine in this series is constructed with high-quality materials designed to withstand the rigors of regular use. The stainless-steel tubs are resistant to chipping and snagging, ensuring that they maintain their efficiency over long periods.

In summary, the Kenmore models 153.330632, 153.330652, 153.33062, and 153.330642 are packed with features aimed at improving the laundry experience. With efficient water usage, versatile wash cycles, user-friendly controls, noise reduction technologies, and durable construction, these machines stand out as reliable choices for modern households seeking an effective laundry solution. As users navigate their laundry tasks, these washing machines promise to deliver performance while keeping convenience and sustainability at the forefront.