Facts to Consider About

the Location

Carefully choose an indoor location for the new water heater. The placement is a very important consideration for the safety of the occupants in the building and for the most economical use of the appliance. This water heater is not for use in manufactured (mobile) homes or outdoor installation.

Whether replacing an old water heater or putting the water

heater in a new location, the following critical points must be observed:

Select a location indoors as close as practical to the gas vent or chimney to which the water heater vent is going to be connected, and as centralized with the water piping system as possible.

Selected location must provide adequate clearances for servicing and proper operation of the water heater.

Property Damage Hazard

AHwater heaters eventually leak

Do n,otinstall without adequate drainage.

Installation of the water heater must be accomplished in such a manner that if the tank or any connections should leak, the flow wilt not cause damage to the structure. For this reason, it is not advisable to install the water heater in an attic or upper floor. When such locations cannot be avoided, a suitable metal drain pan should be installed under the water heater. Metal drain pans are available at your local Sears or hardware store. Such a drain pan must have a minimum length and width of at least 2 inches (51 mm) greater than the water heater dimensions and must be piped to an adequate drain. The pan must not restrict combustion air flow.

Water heater life depends upon water quality, water pressure and the environment in which the water heater is installed. Water heaters are sometimes installed in locations where leakage may result in property damage, even with the use of a metal drain pan piped to a drain. Unanticipated damage can be reduced or prevented by a leak detector or water shut-off device used in conjunction with a piped metal drain pan. These devices are available from some plumbing supply wholesalers and retailers, and detect and react to leakage in various ways:

Sensors mounted in the metal drain pan that trigger an alarm or turn off the incoming water to the water heater when leakage is detected.

Sensors mounted in the metal drain pan that turn off the water supply to the entire home when water is detected in the metal drain pan.

Water supply shut-off devices that activate based on the water pressure differential between the cold water and hot water pipes connected to the water heater.

Devices that wilt turn off the gas supply to a gas water heater while at the same time shutting off its water supply.

Fire or Explosion Hazard

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

Avoid all ignition sources if you smell LP gas.

Do not expose water heater control to excessive gas pressure.

Use only gasshewn on ratingplate.

Maintain required clearances to combustibles.

Keep ignition sources away frcrn faucets after

_,

extended period of non-use.

,dlnLj

d_j_,

Read instruction n_anual before

 

 

installing, using or servicing

 

_i_J

water heater.

 

INSTALLATIONS IN AREAS WHERE FLAMMABLE LIQUIDS (VAPORS) ARE LIKELY TO BE PRESENT OR STORED (GARAGES, STORAGEAND UTILITYAREAS, ETC.): Flammable liquids (such as gasoline, solvents, propane [LP or butane, etc.] and other substances such as adhesives, etc.) emit flammable vapors which can be ignited by a gas water heater's pilot light or main burner. The resulting flashback and fire can cause death or serious burns to anyone in the area. Even though this water heater is a flammable vapor ignition resistant water heater and is designed to reduce the chances of flammable vapors being ignited, gasoline and other flammable substances should never be stored or used in the same vicinity or area containing a gas water heater or other open flame or spark producing appliance.

Also, the water heater must be located and/or protected so it is not subject to physical damage by a moving vehicle.

Fire Hazard

For continued protection against riskof fire:

Do not install water heater on carpeted floor.

Do not operate water heater if flood damaged.

This water heater must not be installed directly on carpeting. Carpeting must be protected by metal or wood panel beneath the appliance extending beyond the full width and depth of the appliance by at least 3 inches (76.2mm) in any direction, or if the appliance is installed in an alcove or closet, the entire floor must be covered by the panel. Failure to heed this warning may result in a fire hazard.

Page 9
Image 9
Kenmore 153.33062, 153.330652, 153.330632, 153.330642 owner manual Facts to Consider About Location, Property Damage Hazard

153.330642, 153.33062, 153.330632, 153.330652 specifications

The Kenmore model series 153.330632, 153.330652, 153.33062, and 153.330642 represent a versatile lineup of washing machines designed to cater to a variety of laundry needs. Each model comes equipped with unique features and technologies aimed at enhancing the user's washing experience while ensuring reliability and performance.

One of the standout features across these models is their efficient water usage. Designed with modern technology, these machines incorporate advanced sensors that adjust the water level according to the load size. This not only conserves water but also contributes to lower utility bills, making them environmentally friendly options.

In terms of operation, the Kenmore models boast a range of wash cycles tailored to different fabric types and soil levels. From delicate items to heavy-duty fabrics, users can choose the appropriate cycle to ensure optimal cleaning without damaging their garments. The presence of a quick wash option is also a highlight, enabling users to clean lightly soiled items in a fraction of the time.

The Kenmore series is also designed for user convenience. Features such as a digital display control panel allow for intuitive operation. Users can easily select their desired settings and monitor the wash cycle progress. Additionally, the machines are equipped with a delay start function, which provides flexibility for users to schedule their laundry according to their convenience.

Another notable characteristic of these models is the installation of noise-reducing technologies. This minimizes operational sounds, allowing for quieter washing cycles, which is particularly beneficial for households with infants or those who prefer a tranquil environment.

Durability is a significant aspect of the Kenmore brand. Each machine in this series is constructed with high-quality materials designed to withstand the rigors of regular use. The stainless-steel tubs are resistant to chipping and snagging, ensuring that they maintain their efficiency over long periods.

In summary, the Kenmore models 153.330632, 153.330652, 153.33062, and 153.330642 are packed with features aimed at improving the laundry experience. With efficient water usage, versatile wash cycles, user-friendly controls, noise reduction technologies, and durable construction, these machines stand out as reliable choices for modern households seeking an effective laundry solution. As users navigate their laundry tasks, these washing machines promise to deliver performance while keeping convenience and sustainability at the forefront.