Setting up the system, Connecting the antennas

Setting up the system

KR-V888D (En/T)

8Connecting the antennas

Make connections as shown below.

Do not connect the power cord to a wall outlet until all connections are completed.

Antenna terminal connections

1 Push lever.

2 Insert cord.

3 Return lever.

Preparations

AM loop antenna

The supplied loop antenna is for use indoors. Place it as far as possible from the receiver, TV set, speaker cords and power cord, and adjust the direction for best reception.

AM loop antenna

GND

FM75Ω

FM indoor antenna

ANTENNA

Use an optional antenna adaptor

FM outdoor antenna

FM indoor antenna

The supplied indoor antenna is for temporary use only. For stable signal reception we recommend using an outdoor antenna. Disconnect the indoor antenna when you connect one outdoors.

FM outdoor antenna

Lead the 75Ω coaxial cable connected to the FM outdoor antenna into the room and connect it to the FM 75Ω terminal.

Page 8

Image 8

Kenwood KR-V888D instruction manual Setting up the system, Connecting the antennas

Contents

About the supplied remote control KR-V888D Safety precautions AccessoriesGetting started Unpacking Contents True home theater sound Special featuresUniversal IR InfraRed remote control How to use this manual Special featuresRDS Radio Data System tuner New Traitr transistor adopted in the final stage About the Standby indicator Names and functions of parts Names and functions of parts Setting up the system Connecting the antennas Connecting audio components Microcomputer malfunction6CH input M.INPUT System Control jacks Connecting video components Setting up the system Digital connections AC-3 RF Demodulator DEM-999D Connecting the system control Registering setup codes for Kenwood audio components Connecting the speakers Speaker impedance Preparing the remote control PRE OUT connectionsLoading the batteries Operating distance Using the on-screen display Press the Sound or Setup keyTo quit the OSD mode Move the pointer Surround set up Speaker placementPreparing for surround sound Select the speakers and enter the speaker distance Enter the speaker distance 4Adjust the volume levels of each speakerAdjust the audio input level of the connected components Normal playback Listening to a source component Adjusting the sound Listening with headphones Source Direct playback 6CH.INPUT playback Listening with a graphic equalizerSet the Input Selector to Video Seconds Recording Recording audioRecording video Recording a music source Tuning non-RDSradio stations Select a tuning methodSet the input to tuner Select a broadcast band Tuning radio stations by frequency Direct tuning Listening to radio broadcasts3Enter the frequency Press the Direct key Using the Display key RDS functions Presetting RDS stations RDS Auto Memory Receiving preset RDS stationsSet the broadcast band to FM Store the stations automatically Presetting radio stations manually Receiving preset stations in order P.CALLEnter a preset number 1~40 For 15, press For 20, press Select the program type you desire Tuning by program type PTY searchActivate the PTY search mode Example Searching for a Rock Music broadcast To select another program typeStart the search Tune to a preset RDS station Reserving the desired informationPreparation Stations RDS Auto Memory To cancel EON reservation When listening to the tunerTurn the TA, News and INFO. indicators off TP Traffic Program indication Ambience effects Sound modesDolby Digital AC-3 Dolby Pro Logic Ambience effects DSP modeWhats DSP? Select a surround mode Surround PlayPreparations Source Direct S.DIR Convenient functions To select a DSP modeTo adjust the DSP modes OSD switch Source Direct switchSET UP switch Radio Text switch KR-V888D En/T Getting the most from your remote control Registering setup codes for other componentsFind the setup code of the component to be registered Low battery warning Enter the setup code 8Once setup codes have been entered for allPress the ENT key to store the code you have just input 7Repeat steps 3 to 6 to register additional Operating other components Video key Audio key TV keyPress the operation keys you desire VIDEO1 VCR CD CD TV1 VIDEO2 VCR Changing confirming the operation mode Press ShiftSelect the component to be controlled Execute the desired operations Perform each of the following steps within 5 seconds Make a plan of the macro play you want to set upActivate the macro program mode Select where the macro should be stored Terminate the macro program modePress the keys to be operated in order Repeat steps 1 through 5 to program up to 3 macros Execute the macro play Executing an automatic operationPress the Macro key Setup code correlation Deleting a setup codeChecking a setup code Perform each step within 5 seconds Hold down the ENT key until the backlight flashes twice Enter the 3 digit codeUK including N. Ireland Go to within 5 seconds Press a numeric key Code selection after mode downloadHold your remote to the speaker portion of your telephone Set up code chart VCR Set up codesMaker Set up codes Non-IR codes Set up code chart VCR Set up codes TV Set up codes BPL Satellite Set up codes LD player Set up codesDSS Set up codes DVD Set up codes Cable Set up codes CD Player Set up codes DAT deck Set up codes Cassette deck Set up codesMD Set up codes Misc. audio Set up codes Resetting the Microcomputer Case of difficultyAmplifier Tuner Memory back up function Remote control unitCase of difficulty Specifications Tuner operations Remote operation of other componentsMD recorder operations TV operations VCR operationsLD player operations Satellite tuner operations Function Shift commands Menu Menu Theme Theme Cable tuner operationsDVD player operations + Channel + Select Numeric keys For your records