Preparing for surround sound
4Input the distance to the speakers.
1 Measure the distance from the listening position to each of the speakers.
Jot down the distance to each of the speakers.
Distance to front speakers: | ____ feet (meters) |
Distance to center speaker: | ____ feet (meters) |
Distance to surround speakers: | ____ feet (meters) |
2Use the MULTI CONTROL to select the distance to the front speakers.
The speaker indicator to be adjusted blinks.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| SP |
|
| TI.VOL | L | C | R |
|
|
| FM | DIGITAL |
|
| |||
|
|
|
| MUTE |
| LFE | SW |
|
|
| AM PRO LOGIC S.DIRECT |
|
| ||||
|
|
|
|
|
|
| MHz 3 STEREO MONITOR |
|
| ||||||||
| RDS | EON | PTY | LS |
| S | RS |
|
|
| kHz DOWN MIX | DSP |
|
|
| ||
| TP | TA | NEWS |
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Indication in feet | Indication in meters |
| ||||||||
•The allowable setting range is 1 to 30 feet (0.3 to 9.0 m), adjustable in 1 foot (0.3 m) increments.
3Press the SET UP key.
4Repeat steps 2 and 3 to input the distance for each of the speakers.
5Setup is complete when the input indication reappears.
SP |
| TI.VOL | L | C | R | |
|
| MUTE | LFE |
| SW | |
RDS | EON | PTY |
| |||
LS | S | RS | ||||
TP | TA | NEWS | ||||
|
|
|
Display when all speakers have been selected.
•The speakers you selected appear on the display. Confirm that all the speakers have been correctly selected.
Normal playback
Preparing for playback
17
Some preparatory steps are needed before starting playback.
INPUT MODE
ON/STANDBYAUTO
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
POWER | MUTE |
|
|
|
|
| INPUT SELECTOR | |||||||||||||||||||
|
|
|
| SPEAKER |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
Selecting the input mode
If you have selected a component connected to the CD/DVD, DVD/ 6ch or VIDEO2/MONITOR jacks, make sure that the input mode
setting is correct for the type of audio signal to be used. | 7 |
Selecting MD/TAPE
Select the source name corresponding to the component connected to the MD/TAPE jacks. The initial factory setting is "TAPE". To change the source name associated with the MD/TAPE jacks to "MD," follow the
steps below: | Operations |
2 Hold down the AUTO key for more than 2 seconds. | |
1 Use the INPUT SELECTOR knob to select "TAPE". |
|
• The source indication changes to "MD".
• To return to the original indication, repeat the above procedure.
• You also will need to change the name input to the remote control to "MD".
Input level adjustment (analog sources only)
If the input level of an analog source signal is too high, adjust the input level.
1Use the INPUT SELECTOR knob to select the source who’s input level you want to adjust.
•You can store a separate input level for each input source. If the MONITOR function is on, you can store an input level for when MONITOR is on independently of the input levels for the input sources.
2Press the SOUND key several times until the "INPUT" indica- tion appears.
3Use the MULTI CONTROL to adjust the input level.
| SP |
| TI.VOL | L | C | R | FM | DIGITAL |
|
|
|
|
| MUTE | LFE |
| SW | AM PRO LOGIC S.DIRECT |
|
| |
|
|
|
| MHz 3 STEREO MONITOR |
|
| ||||
| RDS | EON | PTY | LS | S | RS | kHz DOWN MIX | DSP |
|
|
| TP | TA | NEWS |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
•The adjustment mode is displayed for approximately eight sec- onds.
•The input level may be adjusted to any one of three settings: 0,
4Press the SOUND key to return to the input indication.
The speaker indicator lights.
SP | A B | TI.VOL | L | C | R | |
CLIP |
| MUTE | LFE |
| SW | |
RDS | EON | PTY |
| |||
LS | S | RS | ||||
TP | TA | NEWS | ||||
|
|
|
Press the SPEAKER key to switch the speakers on and off.
Turning on the receiver
1Turn on the power to the related components.
2Turn on the power to this receiver by pressing POWER and ON/ STANDBY keys.