Preparing for surround sound
15
Sit in your normal listening position and listen to the test tone. Adjust the volume levels for the speakers until all speakers seem to be equally loud.
1Use the MULTI CONTROL knob or the 5/° keys to adjust the volume when the test tone is being output from the speaker channel to be adjusted.
The channel indication blinks while the test tone is being output.
SP | A | TI.VOL | L | C | R | FM | DIGITAL | |
AM PRO LOGIC S.DIRECT | ||||||||
|
| MUTE | LFE |
| SW | |||
|
|
| MHz 3 STEREO MONITOR | |||||
RDS | EON | PTY |
| |||||
LS | S | RS | kHz DOWN MIX | DSP | ||||
TP | TA | NEWS | ||||||
|
|
|
|
| ||||
The test tone issues from the speakers for 2 seconds at a time in the following sequence:
Lch = Cch = Rch = RS = LS = SW = Lch•If you change the volume level settings for the speakers while listening to music, the settings referred to on this page are also changed.
¢
•If the speaker setting selects are changed, the speaker level settings are reset.
2Press the SET UP or display operation 2 [Next] key.•The receiver enters the mode for inputting the distance to the speakers.
4Input the distance to the speakers.1 Measure the distance from the listening position to each of the speakers.Jot down the distance to each of the speakers.Distance to front speakers: | ____ feet (meters) |
Distance to center speaker: | ____ feet (meters) |
Distance to surround speakers: | ____ feet (meters) |
2Use the MULTI CONTROL knob or the 5/°keys to select the distance to the front speakers.
The speaker indicator to be adjusted blinks.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| SP |
| A |
| TI.VOL L | C | R |
|
|
| FM | DIGITAL |
|
| |||
|
|
|
|
|
| AM PRO LOGIC S.DIRECT |
|
| |||||||||
|
|
|
|
| MUTE |
| LFE |
| SW |
|
|
| MHz 3 STEREO MONITOR |
|
| ||
|
|
|
|
|
|
|
|
|
|
| |||||||
| RDS |
| EON | PTY | LS | S | RS |
|
|
| kHz DOWN MIX | DSP |
|
|
| ||
| TP | TA | NEWS |
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Indication in feet | Indication in meters |
|
|
|
| |||||
•The allowable setting range is 1 to 30 feet (0.3 to 9.0 m), adjustable in 1 foot (0.3 m) increments.
3Press the SET UP or display operation 2 [Next] key.4Repeat steps 2 and 3 to input the distance for each of the speakers.5Setup is complete when the input indication reappears.SP A | L | R |
|
| SW |
Display when all speakers have been selected.
•The speakers you selected appear on the display. Confirm that all the speakers have been correctly selected.
If the input level of an analog source signal is too high, adjust the input level.
1 Use the INPUT SELECTOR knob to select the source who’s input level you want to adjust.
• You can store a separate input level for each input source. If the
MONITOR function is on, you can store an input level for when Preparation
MONITOR is on independently of the input levels for the input sources.
2 Press the SOUND key several times until the “INPUT” indication appears.3Use the MULTI CONTROL knob or the 5/° keys to adjust the input level.
|
|
|
|
|
|
|
|
| FM | DIGITAL |
|
|
| SP |
| A |
| TI.VOL | L | C | R | AM PRO LOGIC S.DIRECT |
|
| |
|
|
|
|
| MUTE | LFE |
| SW | MHz 3 STEREO MONITOR |
|
| |
| RDS |
| EON | PTY | LS | S | RS | kHz DOWN MIX | DSP |
|
| |
| TP | TA | NEWS |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
•The adjustment mode is displayed for approximately eight seconds.
•The input level may be adjusted to any one of three settings: 0,