Kenwood KRF-V8030D, VR-409 Digital connections, DVD, VIDEO2, VIDEO3, D-AUTO, D-AUTO, ANALOG, D-AUTO, ANALOG, D-MANUAL, D-MANUAL, 6CH INPT, D-MANUAL, D-MANUAL, MD player, CD player

Digital connections

The digital in jacks can accept DTS, Dolby Digital (AC-3), or PCM signals. Connect components capable of outputting DTS, Dolby Digital (AC-3), or standard PCM (CD) format digital signals.

If you have connected any digital components to the receiver, be sure to read the “Input mode settings” section on this page carefully.

DVD	VIDEO 3	MONITOR
CD/DVD	VIDEO 3	MONITOR
OPTICAL	OPTICAL	OPTICAL

Setting up the system

Input mode settings		9
CD, DVD, VIDEO2, and VIDEO3 inputs each include jacks for digital		9
audio input and analog audio input.
You must select beforehand which type of input is to be used for each
connected component.
The initial factory setting is to use the digital audio signal for
playback (CD, DVD, VIDEO2, VIDEO3).
To use the analog audio input for playback instead (if, for example, you
have connected a VCR to the VIDEO2 or VIDEO3 input), you must set
the input mode for the corresponding input to the analog mode.		Preparations
After completing connections and turning on the receiver, follow the		Preparations

steps below.
	INPUT SELECTOR

VIDEO 2

COAXIAL

DIGITAL IN

DIGITAL OUT

Optical fiber cable

OPTICAL DIGITAL IN (AUDIO)

MD player

OPTICAL DIGITAL OUT (AUDIO)

Component with an DTS, DolbyDigital, or PCM OPTICALDIGITAL OUT

Connect the video signal and analog audio signals to the VIDEO 3 jacks. (See "Connecting video components".)

INPUT MODE

1Use the INPUT SELECTOR knob to select CD, DVD, VIDEO2, or VIDEO3.2 Press the INPUT MODE key.Each press switches the setting as follows:In DTS play mode

1 D-AUTO(digital input, auto sound)

2 D-MANUAL(digital input, manual sound)

In DVD play mode

1 D-AUTO(digital input, auto sound)

2 D-MANUAL(digital input, manual sound)

3 6CH INPT (DVD 6CH input)

4 ANALOG (analog input, manual sound)

COAXIAL DIGITAL OUT (AUDIO)

RF digital demodulator (DEM-9991D) (sold separately)

OPTICAL DIGITAL OUT (AUDIO)

CD player

COAXIAL DIGITAL OUT (AUDIO)

Component with an DTS, Dolby

Digital, or PCM COAXIAL

DIGITAL OUT

Connect the video signal and analog audio signals to the VIDEO 2 jacks. (See "Connecting video components".)

In other mode than DTS or DVD play mode

1 D-AUTO(digital input, auto sound)

2 D-MANUAL(digital input, manual sound)

3 ANALOG (analog input, manual sound)

Digital input:

Select this setting to play digital signals from a DVD, CD, or LD player.

Analog input:

Select this setting to play analog signals from a cassette deck, VCR, or turntable.

Auto sound:

In the auto sound mode (AUTO SOUND indicator lights), the receiver selects the listening mode automatically during playback to match the type of input signal (Dolby Digital, PCM, DTS ) and the speaker setting. The initial factory setting is auto sound on.

DOLBY DIGITAL RF	LD player
OUT (AUDIO)
PCM OUT

To connect an LD player with a DIGITAL RF OUT, connect the LD player to the KENWOOD RF digital demodulator (DEM-9991D). Next, connect the DIGITAL OUT jacks of the demodulator to the DIGITAL IN jacks of the receiver.

Connect the video signal and analog audio signals to the VIDEO 2 or VIDEO 3 jacks. (See "Connecting video components".)

To keep the receiver set to the currently selected listening mode, use the INPUT MODE key to select “D-MANUAL” (manual sound). However, even when this setting is selected, there may be cases in which the listening mode is selected automatically to match a Dolby Digital source signal depending on the combination of listening mode and source signal.