KitchenAid W10515677C manual Vacation and Moving Care, To Shut Down the Ice Maker

NOTE: Make sure the plastic spacer from the right-hand side of the cutter grid bracket stays with the cutter grid.

	D
A
B	E
C
	F

A. Cutter grid harness	D. Ice level sensor harness
B. Screw	E. Plastic spacer
C. Cutter grid	F. Screw

8.Remove the mounting screw that holds the water pan in place. Pull out on the front of the water pan.

9.Disconnect the pump bracket from the water pan and unplug the water pan drain pump.

A
B	D
C

A. Water pan	C. Drain cap
B. Water pan screw	D. Drain pump cover

10.Remove, clean and replace the ice scoop and ice scoop holder.

NOTE: On some models, the ice scoop holder is located in the upper left of the unit, and on other models, the ice scoop holder is located in the lower left of the unit.

■After removing the ice scoop, remove the holder by removing the 2 screws.

NOTE: On some models, remove the holder by lifting up on the ice scoop holder and then out.

■Wash the ice scoop holder along with the other interior components using the following instructions.

■Replace the ice scoop holder by replacing the screws or on some models, pushing in on the holder and then down.

A

A. Ice scoop holder

11.Wash the interior components (cutter grid, exterior of hoses, and water pan) and the storage bin, door gasket, ice scoop, and ice scoop holder with mild soap or detergent and warm water. Rinse in clean water. Then clean the same parts with a solution of 1 tbs (15 mL) of household bleach in 1 gal. (3.8 L) warm water. Rinse again thoroughly in clean water.

NOTE: Do not remove hoses. Do not wash plastic parts in dishwasher. They cannot withstand temperatures above 145°F (63°C).

12.To replace the water pan, set the water pan inside the ice bin. Hook up the water pan pump. Snap the pump bracket back onto the water pan and place back into position. Secure the water pan by replacing the mounting screw.

13.Check the following:

■Drain cap from the water pan is securely in place. If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice.

■Hose from water pan is inserted into storage bin drain opening.

14.Slide the cutter grid back into place and secure it by replacing the right-hand screw and plastic spacer. Then tighten the left-hand screw. Reconnect the cutter grid harness and the ice level sensor harness.

15.Replace the cutter grid cover using the screw that was removed earlier.

16.Gently wipe the control panel with a soft, clean dishcloth using warm water and a mild liquid dish detergent.

17.Plug in ice maker or reconnect power.

18.After cleaning, make sure that all controls are set properly and that no control indicators are flashing.

Vacation and Moving Care

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

To Shut Down the Ice Maker:

1.Unplug ice maker or disconnect power.

2.Remove all ice from storage bin.

3.Shut off the water supply.

4.Remove the 2 screws in the lower access panel and the

2 screws from the base grille area of the front panel support. Pull forward to remove the lower access panel.

A

A

B

B

A. Lower access panel screws

B. Base grille screws

5.Disconnect the inlet and outlet lines to water valve. Allow these lines to drain and then reconnect to the valve.

6.Replace lower access panel and screws.

7.Drain water from water pan by removing the drain cap.

8.If the room temperature will drop below 32°F (0°C), water must be removed from the drain line.

For Ice Makers with a Drain Pump Installed:

■Plug in ice maker or reconnect power.

■Turn ice maker off and remove all remaining ice from ice bin.

14