Parameters
19
Group 4Amp Type [Type 1, Type 2, Pre Amp]
Select the type of amp.
Type 1: A standard powered amp for organ, produc-
ing a mild and fat tone.
Type 2: This emphasizes the high range more than
Type 1, producing an uncolored tone.
Pre Amp: The pre-amp will be used. This is the sound
of a direct line-out from the organ.
If you select Type 1 or Type 2, using the front panel
ROTARY section [ON] key to turn the rotary speaker
on will simulate using a rotary speaker. If you turn
this off, a standard speaker will be simulated.
If you select Pre Amp, the powered amp and rotary
speaker will not be used; the sound will be that of a
line-out connection from the organ itself.
Amp Gain [0...99]
Adjust the gain (amplification) when the “Amp Type”
parameter is set to Type 1 or Type 2.
With high settings of this value, the sound will be
distorted more severely when expression/overdrive is
raised.
This setting will not be used if the “Amp Type”
parameter is set to Pre Amp.
Tone Treble [–10...+10]
Adjust the high frequency range of the amp selected
by the “Amp Type” parameter.
Tone Middle [–10...+10]
The mid-frequency range of the amp selected by the
“Amp Type” parameter.
Tone Bass [–10...+10]
Adjust the low frequency range of the amp selected by
the “Amp Type” parameter.
Group 4: Tone Trebel
Tone Middle
Tone Bass
Amp Type: Pre Amp
Pre Amp Reverb
Group 4: Amp Gain
Tone Trebel
Tone Middle
Tone Bass
Amp Type: Amp 1 or Amp 2
Amp 1/2 Rotary
Pre Amp Reverb
Group 5: Rev Routing
Group 5Reverb Type [Room, Hall, Plate]
Select the type of reverb.
Reverb Time [00.25...16.00 (Sec)]
Adjust the reverb time.
The range in which the reverb time can be set will
depend on what is selected for the “Reverb Type”
parameter.
Reverb Mix Level [0...99]
Adjust the amount of reverb.
Rev Routing (Reverb Routing) [Rot->Rev, Rev->Rot]
Specify whether the reverb will be placed before or
after the rotary speaker.
Rot -> Rev: The reverb effect will be applied after the
rotary speaker.
Rev -> Rot: The reverb effect will be applied before
the rotary speaker.
This setting is not used if the “Amp Type” parameter
is set to Pre Amp.
Group 6These settings are not used if the “Amp Type”
parameter is set to Pre Amp.
Horn: 0 Rotor: 100 (Rotary Horn/Rotor Balance)
[0:100...100:0]
Adjust the volume balance between the horn and the
rotor of the rotary speaker.
Horn Slow Speed [0...99]
Adjust the slow rotational speed of the horn.
Horn Fast Speed [0...99]
Adjust the fast rotational speed of the horn.
Rotor Slow Speed [0...99]
Adjust the slow rotational speed of the rotor.
Rotor Fast Speed [0...99]
Adjust the fast rotational speed of the horn.
Horn Up Transit (Horn Up Transition) [0...99]
Adjust the time over which the horn rotation changes
from slow to fast.
Horn Down Transit (Horn Down Transition) [0...99]
Adjust the time over which the horn rotation changes
from fast to slow.
Horn Stop Transit (Horn Stop Transition) [0...99]
Adjust the time over which the horn rotation actually
comes to a stop after you stop the rotation.
Horn Strt Transit (Horn Start Transition) [0...99]
Adjust the time over which the horn reaches the speci-
fied speed after it begins to rotate.