5. Pattern mode

6. Turn the dial to edit the parameter value at that step. If you select

 

“Disabl,” the motion sequence value will not be updated at that step.

 

MOTION DEST

 

MOTION VALUE

 

* Keyboard part ONLY

 

Fx1Ed1(FX1 EDIT1)

 

Disabl, 0...127 (depends on FX TYPE)

 

 

 

 

 

 

Fx1Ed2(FX1 EDIT2)

 

Disabl, 0...127 (depends on FX TYPE)

 

 

 

 

 

 

Fx2Ed1(FX2 EDIT1)

 

Disabl, 0...127 (depends on FX TYPE)

 

 

 

 

 

 

Fx2Ed2(FX2 EDIT2)

 

Disabl, 0...127 (depends on FX TYPE)

 

 

 

 

 

 

Fx3Ed1(FX3 EDIT1)

 

Disabl, 0...127 (depends on FX TYPE)

 

 

 

 

 

 

Fx3Ed2(FX3 EDIT2)

 

Disabl, 0...127 (depends on FX TYPE)

 

 

 

 

 

 

Pitch/Glide(PITCH/GLIDE*)

 

Disabl, -63...+63

 

 

 

/Disabl, 0...127

 

 

 

 

 

 

EGTime(EG TIME)

 

Disabl, 0...127

 

 

 

 

 

 

Pan(PAN)

 

Disabl, L63...R63

 

 

 

 

 

 

Level(LEVEL)

 

Disabl, 0...127

 

 

 

 

 

 

SttPoint(START POINT)

 

Disabl, 0...127

 

 

 

 

 

 

AmpEG(AMP EG)

 

Disabl, Off, On

 

 

 

 

 

 

Roll(ROLL)

 

Disabl, Off, On

 

 

 

 

 

 

Revers(REVERSE)

 

Disabl, 0...127

 

 

 

 

 

 

FxSend(FX SEND)

 

Disabl, Off, On

 

 

 

 

 

 

FxSel(FX SELECT)

 

Disabl, Fx1, Fx2, Fx3

 

 

 

 

 

 

ModSpd(SPEED)

 

Disabl, 0...127

 

 

 

 

 

 

ModDpt(DEPTH)

 

Disabl, 0...127

 

 

 

 

 

 

ModTyp(TYPE)

 

Disab, Saw, Squ, Tri, SH, Env

 

 

 

 

 

 

ModDst(DST)

 

Disabl, Pitch, Amp, Pan, Cutoff

 

 

 

 

 

 

ModBPM(BPM SYNC)

 

Disabl, Off, On

 

 

 

 

 

 

Cutoff(CUTOFF)

 

Disabl, 0...127

 

 

 

 

 

 

EgInt(EG INT)

 

Disabl, -63...+63

 

 

 

 

 

 

Reso(RESONANCE)

 

Disabl, 0...127

 

 

 

 

 

 

FitTyp(TYPE)

 

Disabl, LPF, HPF, BPF, BPF+

 

 

 

 

 

 

The motion sequence you edit will return to the state prior to editing

 

if you switch to another pattern before you write the data. If you want

 

to keep the edited motion sequence, execute the Write operation

 

(☞ p.74 “Saving a pattern”).

 

 

 

 

You cannot use the step keys to turn steps on/off while editing a

 

motion sequence.

 

 

 

 

Depending on the part, some parameters cannot be selected.

 

The REC key will not function while you are editing a motion se-

 

quence.

 

 

 

 

When selecting “MotDest,” you can hold down the shift key and use the dial to select a parameter for which a motion sequence has not yet been recorded, and then use MOTION VALUE to edit the values.

Erasing a motion sequence for a part or effectCLEAR MOTION .....................................................................

Here’s how to erase all motion sequence data for a part or effect in a single operation.

1.If the pattern is playing, press the STOP/CANCEL key to stop play- back.

2. Hold down the shift key, and press step key 5 (CLEAR MOTION). (Key 5 will blink.)

3.Press the motion sequence key of the part (drum, keyboard, accent) or effect whose motion sequence data you want to erase. (You may select more than one.) The selected key(s) will blink.

4.Press step key 5 once again to execute the Clear operation. If you decide to cancel, press the STOP/CANCEL key.

This will erase all motion sequences for the selected part or effect.

71