Korg PS60 026: Tube Pre (Tube PreAmp Modeling), 027: St.TubPre , (Stereo Tube PreAmp Modeling), 028: Mic Model (Mic Modeling + PreAmp)

Effect Guide
98
026: Tube Pre (Tube PreAmp
Modeling)
Thiseffectsimulatesatwo‐stagevacuumtubepreamp.You
canmakeindividualsettingsfortwovacuumtubes
connectedinseries.Thisletsyoucreatethewarmsound
typicalofvacuumtubes.
Saturation [%]
Withhighersettingsofthisvalue,thewaveformwillchange
athighgainlevels,tendingtocausedistortion.Lower
settingsofthisvaluewillproducelinearresponse.
Tube1 Bi as
Thisexpressestheeffectthatchangesinvacuumtubebias
haveonthedistortionofthewaveform.Highersettingsof
thisvaluewillproducedistortionevenatlowgainlevels.
Sincethiswillalsochangetheovertonestructure,youcan
useittocontrolthetonalcharacter.
Tube1 Ph ase
WiththeWetInvertsetting,thephaseofthesignalwillbe
invertedbetweenstage1andstage2.Since“Bias”isapplied
totheinvertedsignalinstage2,thiswillchangethetonal
character.
027: St.TubPre (Stereo Tube PreAmp
Modeling)
Thisisastereovacuumtubepreampsimulator(See“026:
TubePre(TubePreAmpModeling)”onpage 98.).
028: Mic Model (Mic Modeling +
PreAmp)
Thiseffectsimulatesamicandvacuumtubepreamp.You
canchoosefromvarioustypesofmicandpositionstocreate
differingsoniccharacters.
Full
parameter
Quick
parameter Value Explanation
Tube1
Low Cut [Hz] T1 L[Hz] Thru, 21...8.00k
Sets the cutoff
frequency for the low
cut filter of stage 1
Tube1
High Cut
[Hz]
T1 H[Hz] 53...20.00k,
Thru
Sets the cutoff
frequency for the high
cut filter of stage 1
Tube1
Gain [dB] T1 G[Hz] –24.0...+24.0 Sets the input gain for stage 1
Tube1
Saturation
[%]
T1 Saturat 0...100
Sets the input/output
response for stage 1
p.98
Tube1 Bias T1 Bias 0...100 Sets the bias voltage
for stage 1 p.98
Tube1 Phase T1 Phase Normal,
Wet Invert
Turns phase reversal
on/off p.98
Tube2
Low Cut [Hz] T2 L[Hz] Thru, 21...8.00k
Sets the cutoff
frequency for the low
cut filter of stage 2
Tube2
High Cut
[Hz]
T2 H[Hz] 53...20.00k,
Thru
Sets the cutoff
frequency for the high
cut filter of stage 2
Tube2
Gain [dB] T2 G[Hz] –24.0...+24.0 Sets the input gain for stage 2
Tube2
Saturation
[%]
T2 Saturat 0...100
Sets the input/output
response for stage 2
p.98
Tube2 Bias T2 Bias 0...100 Sets the bias voltage
for stage 2 p.98
Tube2
Output Level
[dB]
Lvl [dB] –48.0...+0.0 Sets the output level
Wet/Dry ←Dry, 1 : 99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
Source Off...Tempo Selects a modulation
source for Wet/Dry
Amount –100...+100 Sets the modulation
amount for Wet/Dry
+Tube Pre Amp1 Tube Pre Amp2
Left
Right
Wet / Dry
Output Level
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Invert
-
Mic/Pre Amp - Saturation
In
Out
Saturation = 0
Saturation = 50
Saturation = 100
Bias = 0
Full
parameter
Quick
parameter Value Explanation
Mic Type Mic
Vintage
Dynamic,
Multi
Condenser,
Percussion
Condenser,
Drums Dynamic,
Vocal Dynamic ,
Multi Dynamic,
Vocal
Condenser,
Vocal Tube,
Kick Dynamic
Selects the type of
mic
Mic Position Mic Posit Close, On,
Off, Far
Sets the mic
placement distance
p.99
Tube
Low Cut [Hz] T L[Hz] Thru, 21...8.00k
Sets the frequency of
the low cut filter
In
Out
Satulation = 50
Bias = 0
Bias = 50
Bias = 100
Mic/Pre Amp - Bias
Left
Right
Wet / Dry
Output Level
Wet / Dry
Stereo In - Stereo Out
Tube Pre Amp1 Tube Pre Amp2
Tube Pre Amp1 Tube Pre Amp2
Left
Right
Wet / Dry
Wet / Dry
–
+
–
+
Invert
+Tube Pre AmpMic Simulation
Left
Right
Wet / Dry
Output Level
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out