Korg PS60 051: Lmtr-P4EQ (Limiter - Parametric 4 -Band EQ), 052: Limtr-Phsr (Limiter - Phaser)

Effect Guide
110
051: Lmtr-P4EQ (Limiter -
Parametric 4 -Band EQ)
Thiseffectcombinesamonolimiterandafour‐band
parametricequalizer.Youcanchangetheorderofthe
effects.
Ratio
Threshold [dB]
Gain Adjust [dB]
Thisparametersetsthesignalcompression“[L]Ratio.”
Compressionisappliedonlywhenthesignallevelexceeds
the“Threshold”value.
Adjusttheoutputlevelusingthe“GainAdjust”parameter,
sincecompressioncausestheentireleveltobereduced.
052: Limtr-Phsr (Limiter - Phaser)
Thiseffectcombinesamonolimiterandaphaser.Youcan
changetheorderoftheeffects.
Full
parameter
Quick
parameter Value Explanation
Limiter
Ratio L Ratio 1.0 : 1...
50.0 : 1, Inf : 1
Sets the signal
compression ratio
p.110
Threshold
[dB] L Trsh[dB] –40...0
Sets the level above
which the
compressor is applied
p.110
Attack L Attack 1...100 Sets the attack time
Release L Release 1...100 Sets the release time
[Gain Adjust
[dB] L G [dB] –Inf, –38...+24
Sets the limiter
output gain p.110
Parametric 4- Band EQ
Trim E Trim 0...100 Sets the parametric
EQ input level
Band1
Cutoff [Hz] E1 F[Hz] 20...1.00k Sets the center frequency of Band 1
Band1 Q E1 Q 0.5...10.0 Sets the bandwidth of
Band 1 p.87
Band1
Gain [dB] E1 G[dB] –18...+18 Sets the gain of Band 1
Band2
Cutoff [Hz] E2 F[Hz] 50...5.00k Sets the center frequency of Band 2
Band2 Q E2 Q 0.5...10.0 Sets the bandwidth of
Band 2 p.87
Band2
Gain [dB] E2 G[dB] –18...+18 Sets the gain of Band 2
Band3
Cutoff [Hz] E3 F[Hz] 300...10.00k Sets the center frequency of Band 3
Band3 Q E3 Q 0.5...10.0 Sets the bandwidth of
Band 3 p.87
Band3
Gain [dB] E3 G[dB] –18...+18 Sets the gain of Band 3
Band4
Cutoff [Hz] E4 F[Hz] 500...20.00k Sets the center frequency of Band 4
Band4 Q E4 Q 0.5...10.0 Sets the bandwidth of
Band 4 p.87
Band4
Gain [dB] E4 G[dB] –18...+18 Sets the gain of Band 4
Routing Route Lmt → P4EQ,
P4EQ → Lmt
Switches the order of
the limiter and
parametric EQ
Wet/Dry ←Dry, 1 : 99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
Source Off...Tempo Selects a modulation
source for Wet/Dry
Amount –100...+100 Sets the modulation
amount for Wet/Dry
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Routing
Limiter
Trim
Parametric 4Band EQ
Limiter
Gain Adjust
Envelope - Control
Full
parameter
Quick
parameter Value Explanation
Limiter
Ratio L Ratio 1.0 : 1...
50.0 : 1, Inf : 1
Sets the signal
compression ratio
p.110
Threshold
[dB] L Trsh[dB] –40...0
Sets the level above
which the
compressor is applied
p.110
Attack L Attack 1...100 Sets the attack time
Release L Release 1...100 Sets the release time
Gain Adjust
[dB] L G [dB] –Inf, –38...+24
Sets the limiter
output gain p.110
Phaser
LFO
Waveform
Triangle,
Sine
Selects the LFO
Waveform
LFO Freq
[Hz] P LFO [Hz] 0.02...20.00 Sets the speed of the LFO
Manual P Manual 0...100
Sets the frequency
where the effect is
applied
Depth P Depth 0...100 Sets the depth of LFO
modulation
Resonance P Reso –100...+100 Sets the resonance
amount p.99
Output
Mode P Out Normal, Wet Invert
Selects the phaser
output mode p.109
[Phs] Wet/
Dry P W/D
–Wet...
–1 : 99, Dry,
1 : 99...Wet
Sets the phaser effect
balance p.91, p.99
[Phs] Source Off...Tempo
Selects the phaser’s
Wet/Dry modulation
source
[Phs]
Amount –100...+100
Sets the phaser’s Wet/
Dry modulation
amount
Routing ←
Limiter →
Phaser,
Phaser →
Limiter
Switches the order of
the limiter and phaser
p.107
Input Level
Output Level
Threshold
Ratio=1.0 : 1
Ratio=2.0 : 1
Ratio=4.0 : 1
Ration=Inf : 1
Louder
Louder
Time
Level
Threshold
Ratio=Inf : 1
Ratio=2.0 : 1
Ratio=4.0 : 1
Dry Ratio=1.0 : 1
Limiter - Threshold / Ratio
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
+
Routing
Limiter
Limiter
Gain Adjust
Envelope - Control
Phaser
Phaser
Resonance
LFO: Tri / Sine
Phaser Wet / Dry
Normal
Wet Invert
Output Mode
–
+