Korg PS60 019: St. Record (Stereo Analog Record), 020: OD Wah (Overdrive/Hi.Gain Wah)

Effect Guide
94
019: St. Record (Stereo Analog
Record)
Thiseffectsimulatesthenoisecausedbyscratchesanddust
onanalogrecords.Italsoreproducessomeofthe
modulationcausedbyawarpedturntable.
Flutter
Thisparameterenablesyoutosetthedepthofthe
modulationcausedbyawarpedturntable.
Click Level
Thisparameterenablesyoutosettheleveloftheclicknoise
thatoccursonceeveryrotationoftheturntable.This
simulationreproducesrecordnoise,andthenoisegenerated
afterthemusiconavinylrecordfinishes.
020: OD Wah (Overdrive/Hi.Gain
Wah)
ThisdistortioneffectutilizesanOverdrivemodeandaHi‐
Gainmode.Controllingthewaheffect,the3‐bandEQ,and
theampsimulationwillallowyoutocreateversatile
distortionsounds.Thiseffectissuitableforguitarandorgan
sounds.
Full
parameter
Quick
parameter Value Explanation
Pre EQ
EQ Trim 0...100 Sets the EQ input level
Pre EQ Cutoff
[Hz] 300...10.00k Sets the EQ center frequency
Pre EQ Q 0.5...10.0 Sets the EQ band
width
Pre EQ Gain
[dB] PEQ [dB] –18.0...+18.0 Sets the EQ gain
Speed Spd/RPM 33 1/3, 45, 78Sets the r.p.m. of a
record
Flutter ←0...100 Sets the modulation
depth p.94
Noise
Density Noise Dens 0...100 Sets the noise density
Noise Tone 0...100 Sets the noise tone
Noise Level NoiseLevel 0...100 Sets the noise level l
Source Off...Tempo
Selects the
modulation source
for the noise level
Amount –100...+100
Sets the modulation
amount of the noise
level
Click Level ClickLevel 0...100 Sets the click noise
level p.94
Source Off...Tempo
Selects the modulation
source for the click
noise level
Amount –100...+100
Sets the modulation
amount of the click
noise level
Wet/Dry Dry, 1 : 99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
Source Off...Tempo Selects a modulation
source for Wet/Dry
Amount –100...+100 Sets the modulation
amount for Wet/Dry
Left
Right
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
Analog Record
Simulation
Pre EQ
Pre EQ
EQ Trim
EQ Trim
Full
parameter
Quick
parameter Value Explanation
Wah ←Off, On Switches Wah on/off
p.95
Source Off...Tempo
Selects the
modulation source
that switches the Wah
on and off
Switch Mode Toggle,
Moment
Selects the switching
mode for the
modulation source
that switches the Wah
on and off p.95
Sweep
Range –10...+10 Sets the range of Wah p.95
Sweep
Source Src Off...Tempo
Selects the
modulation source
that controls the Wah
p.95
Drive Mode Mode Overdrive,
Hi-Gain
Switches between
overdrive and hi-gain
distortion
Drive ←1...100 Sets the degree of
distortion p.95
Pre Low Cut 0...10
Sets the low range
cut amount of the
distortion input p.95
Output Level ←0...50 Sets the output level
p.95
Source Off...Tempo
Selects the
modulation source
for the output level
Amount –50...+50
Sets the modulation
amount of the output
level
Low Cutoff
[Hz] 20...1.00k
Sets the center
frequency for Low EQ
(shelving type)
Gain [dB] Low G[dB] –18...+18 Sets the gain of Low
EQ
Mid1Cutoff
[Hz] 300...10.00k
Sets the center
frequency for Mid/
High EQ 1 (peaking
type)
Q 0.5...10.0
Sets the band width
of Mid/High EQ 1
p.87
Gain [dB] Mid1 G[dB] –18...+18 Sets the gain of Mid/
High EQ 1
Mid2 Cutoff
[Hz] 500...20.00k
Sets the center
frequency for Mid/
High EQ 2 (peaking
type)
Q 0.5...10.0
Sets the band width
of Mid/High EQ 2
p.87
Gain [dB] Mid2 G[dB] –18...+18 Sets the gain of Mid/
High EQ 2
Direct Mix 0...50
Sets the amount of
the dry sound mixed
to the distortion
Speaker
Simulation SpeakerSim Off, On Switches the speaker
simulation on/off
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Amp Simulation
3 Band PEQ
Output Level
Direct Mix
Pre Low-cut
D
-mod
Wah
Mode: Overdrive / Hi-Gain
Drive
Driver