60
“Destination 1–6” and “Value 1–6”
The parameters that can be controlled and their range of val-
ues are as follows.
LPF Fc (Low Pass Filter Cutoff Frequency)
[–99…+00…+99]
Adjusts the low pass filter cutoff frequency of program OSC
1/2. This will affect the brightness of the sound. The param-
eter will be controlled in the same way as when CC#74 is
received. (☞p.175)
Reso.HP (Resonance/High Pass Filter Cutoff
Frequency) [–99…+00…+99]
Adjusts the resonance level of the low pass filter or the cut-
off frequency of the high pass filter for program OSC 1/2.
The parameter that is controlled will depend on the filter
type specified for the program. The parameter will be con-
trolled in the same way as when CC#71 is received. (☞p.175)
F EG Int (Filter EG Intensity) [–99…+00…+99]
Adjusts the filter EG intensity (the depth of the filter EG) for
program OSC1/2. The parameter will be controlled in the
same way as when CC#79 is received. (☞p.175)
A Vel I. (Amp Velocity Intensity) [–99…+00…+99]
Adjusts the amp velocity intensity (the degree to which
velocity will affect the amp) for program OSC 1/2. This con-
trols the Amp Modulation “Velocity Intensity” parameter
(☞p.22 6–2b).
F.A EG A (Filter/Amp EG Attack Time)
[–99…+00…+99]
Adjusts the EG attack times of the program OSC 1/2 filter
and amp. To maximize the result of this adjustment, the
Amp EG sustain level, attack level, start level modulation,
and attack time modulation will also be adjusted at the same
time. The parameter will be controlled in the same way as
when CC#73 is received. (☞p.175)
F.A EG D (Filter/Amp EG Decay Time)
[–99…+00…+99]
Adjusts the EG decay time and slope time of the program
OSC 1/2 filter and amp. The parameter will be controlled in
the same way as when CC#75 is received. (☞p.175)
F.A EG S (Filter/Amp EG Sustain Level)
[–99…+00…+99]
Adjusts the EG sustain level of the program OSC 1/2 filter
and amp. The parameter will be controlled in the same way
as when CC#70 is received. (☞p.175)
F.A EG R (Filter/Amp EG Release Time)
[–99…+00…+99]
Adjusts the EG release time of the program OSC 1/2 filter
and amp. The parameter will be controlled in the same way
as when CC#72 is received. (☞p.175)
F EG A (Filter EG Attack Time) [–99…+00…+99]
F EG D (Filter EG Decay Time) [–99…+00…+99]
F EG S (Filter EG Sustain Level) [–99…+00…+99]
F EG R (Filter EG Release Time) [–99…+00…+99]
These adjust only the filter parameter as in “A (Attack
Time),” “D (Decay Time),” “S (Sustain Level),“ or “R
(Release Time)” respectively. (☞PROG 4–5a)
A EG A (Amp EG Attack Time) [–99…+00…+99]
A EG D (Amp EG Decay Time) [–99…+00…+99]
A EG S (Amp EG Sustain Level) [–99…+00…+99]
A EG R (Amp EG Release Time) [–99…+00…+99]
These adjust only the amp parameter as in “A (Attack
Time),” “D (Decay Time),” “S (Sustain Level),“ or “R
(Release Time)” respectively. (☞PROG 6–3a, 6–6a)
LFO1 Sp (LFO1 Speed) [–199…+00…+199]
Adjusts the LFO1 speed of program OSC 1/2. The parame-
ter will be controlled in the same way as when CC#76 is
received. (☞p.175)
PLFO1 I. (Pitch LFO1 Intensity)
[–12.00…+00.00…+12.00]
Adjusts the program OSC 1/2 pitch LFO1 intensity (the
depth of pitch modulation produced by LFO1). The parame-
ter will be controlled in the same way as when CC#77 is
received. (☞p.175)
LFO1 Fd (LFO1 Fade) [–99…+00…+99]
Adjusts the program OSC 1/2 LFO1 “Fade” parameter (the
time from when the LFO begins to take effect until it reaches
the maximum level; 3–1a ☞p.14).
LFO1 Dl (LFO1 Delay) [–99…+00…+99]
Adjusts the program OSC 1/2 pitch LFO1 delay (the time
from note-on until the LFO begins to take effect). The
parameter will be controlled in the same way as when
CC#78 is received. (☞p.175)
P.Strch (Pitch Stretch) [–12…+00…+12]
Simultaneously adjusts the program OSC 1/2 Transpose
and Tune parameters. This lets you create a rich variety of
tonal changes without impairing the character of the origi-
nal sound.
This controls the same parameters as Performance Editor -
“Stretch (Pitch Stretch)” (0–2b). (☞p.4)
Dtune 1(Detune 1) [–1200…+0000…+1200]
Adjusts the tuning of program OSC 1. This controls the
OSC1 Multisample “Tune” parameter (1–2c ☞p.8).
Dtune 2 (Detune 2) [–1200…+0000…+1200]
Adjusts the tuning of program OSC 2. This controls the
OSC2 Multisample “Tune” parameter (1–2c ☞p.8).
This is valid only if the program’s “Oscillator Mode”
(1–1a ☞p.6) is set to Double.
Hold [Off, PRG, On]
Controls the program’s Voice Assign - “Hold” parameter (1–
1b ☞p.6).
If you turn this Off, the OSC1/2 Amp EG Release Time
parameter will be set to 0 in order to make full use of the
effect.
Normally you can make effective use of this with a drum
program. When you turn this Off, the key-off timing will be
valid, letting you use the key-on/off timing to control the
gate time. Sometimes you can obtain an interesting effect by
turning this Off for a previously-created drum track.