Korg X50 Load Preload Data, microX: , Change all bank references, Half Damper Calibration

GLOBAL

123456

To write a drum kit or user arpeggio pattern, execute the

appropriate utility. (☞4–1 “Write Drum Kits,” 5–1 “Write

Arpeggio Patterns”)

Load Preload Data

This command loads the preload data into internal memory.

Before loading this data, you must uncheck the “Mem-

ory Protect” (0–2b) setting for the data that you want to

load. If the setting is still checked when you attempt to

load the data, a dialog box will indicate “Memory Pro-

tected,” and it will not be possible to load the data.

1Select “Load Preload Data,” and access the dialog box.

2In the “Kind” ﬁeld, select the data that you want to load.

If you selected Program or Combination, move the cur-

sor down and select All, Bank, or Single to specify the

range of data that will be loaded.

All: Data for all programs or combinations will be

loaded.

Bank: Data will be loaded in units of one bank. In this

case, move the cursor down and select the bank whose

data you want to load.

Single: Data for one program or combination will be

loaded. In this case, move the cursor down to select the

data that you want to load.

If you selected Multi DrumKit or Arpeggio Pattern,

move the cursor down and select either All or Single to

specify the range of data that will be loaded.

microX: You can also choose either All or Single even if

you selected Ext. Control Setup.

All: Data for all multi set, drum kits or arpeggio patterns

will be loaded.

Single: Data for one multi set, drum kit or arpeggio pat-

tern will be loaded. In this case, move the cursor down to

select the data that you want to load.

3If you are loading in units of Bank or Single, use the

“To” ﬁeld to select the loading destination.

4To load the data, press the [MENU/OK] button. To can-

cel, press the [EXIT/CANCEL] button.

If you turn on the power while holding down the

[MENU/OK] button and the [EXIT/CANCEL] button,

the “Load All” operation will be executed automati-

cally (the LCD will display a message of “Now Writing

Internal Memory”), and all data be loaded.

Change all bank references

This command changes all program banks speciﬁed for tim-

bres in combinations or tracks of multi sets.

1Select “Change all bank references” to access the dialog

box.

X50

microX

2To execute this command for combinations, check “Com-

bination.” To execute this command for multi sets, check

“Multi.”

3Specify the banks to be changed (“Program Bank”).

4To execute the Change All Bank References command,

press the [MENU/OK] button. To cancel, press the

[EXIT/CANCEL] button.

If you change two or more different banks to the same

bank, it will not be possible to use this function to

change them back to different banks. Be careful that the

change destination banks do not overlap.

Half Damper Calibration

If a damper pedal that supports half damper (the separately

sold DS–1H option) is connected to the rear panel DAMPER

jack, here’s how you can adjust the sensitivity if the damper

effect is not applied appropriately.

1Connect the half damper pedal to the DAMPER jack.

2Select “Half Damper Calibration” to access the dialog

box.

3Press the half damper pedal, and then release the pedal.

4Press the [MENU/OK] button.

If the adjustment could not be performed correctly, an

error message will appear. Please repeat the procedure.

Since the operation of the half damper pedal is delicate,

please use the separately sold DS–1H option. If any

other pedal is used, the correct effect may not be

obtained, or adjustment may not be possible.

All All data

Program All All program data

Program Bank All program data of a bank

Program Single Data for one selected program

Combination All All combination data

Combination Bank All combination data of a bank

Combination Single Data for one selected combination

Multi All Data for all multi sets

Multi Single Data for one selected multi set

DrumKit All All drum kit data

DrumKit Single Data for one selected drum kit

Arpeggio Pattern All All arpeggio pattern data

Arpeggio Pattern Single Data for one selected arpeggio pattern

microX: Ext. Control Setup All

Data for all external control sets

microX: Ext. Control Setup Single

Data for one selected external control

set

Global Setting Global setting data