Manuals / Kuhn Rikon / Kitchen Appliance / Mixer

Kuhn Rikon 3100 instruction manual Fill Level, Unloading, Mixer Operation

Models: 3100

1 36

Download 36 pages 41.93 Kb

Page 23

FILL LEVEL

3100ST 006046 010507

MIXER OPERATION

Always refer to OPERATING SAFETY PRECAUTIONS and SAFETY DECALS in SAFETY section of this manual before operating this mixer.

FILL LEVEL

Do not overload mixer! Overloading causes excessive horsepower requirements, increased strain on mixer driveline and poor mixer performance.

The design of the Reel Auggie and Commercial Reel Mixer requires that there be adequate space to allow the feed to move in and around the reel chamber. If the reel is completely covered, it cannot efficiently mix the materials. The reel cross tubes should always be visible at the top of their rotation to allow this mixing space.

Do not exceed full line as shown in diagram.

UNLOADING

After the ration has been thoroughly mixed, open the mixer door to begin unloading. The discharge door opening determines the flow of feed from the mixer. The door must be opened far enough to prevent separation of materials. Optional door flow control plates are available to help prevent separation.

To stop the flow of feed, close the door, then shut off the mixer.

Back to Table of ContentsKuhn Knight, Inc.23

1501 West 7th Ave., Brodhead, WI 53520

701 Cherry Ave., Greeley, CO 80632

Image 23

Kuhn Rikon 3100 instruction manual Fill Level, Unloading, Mixer Operation

Contents

3100 Series Reel AuggieCommercial Reel Mixers Copyright 2004 Kuhn Knight, Inc TABLE OF CONTENTSADDITIONAL MANUALS USING THIS MANUALINTRODUCTION READ THE OPERATOR’S MANUAL SAFETYUNDERSTANDING SAFETY WORDS AND SYMBOLS FOLLOW SAFETY INSTRUCTIONS AND PRECAUTIONSBack to Table of ContentsKuhn Knight, Inc.5 OPERATING SAFETY PRECAUTIONSSAFETY UNIT PART NO SAFETY DECALSSAFETY Figure B SAFETYSAFETY DECALS Figure AFigure E SAFETYSAFETY DECALS Figure DFigure H SAFETYSAFETY DECALS Figure GShields removed for illustrative purposes SAFETY DECAL PLACEMENT MODEL 3115 S/N A0028 AND BEFORESAFETY Back to Table of ContentsShields removed for illustrative purposes SAFETY DECAL PLACEMENT MODEL 3115 S/N A0029 AND AFTERSAFETY Back to Table of ContentsShields removed for illustrative purposes SAFETY DECAL PLACEMENT MODELSAFETY Back to Table of ContentsShields removed for illustrative purposes SAFETY DECAL PLACEMENT MODELS 3125 ANDSAFETY Back to Table of ContentsBack to Table of Contents SAFETY DECAL PLACEMENT MODELSSAFETY Back to Table of ContentsKuhn Knight, Inc.15 SAFETY DECAL PLACEMENT MODELS 3150, 3160, 3170 ANDSAFETY Electric Motor Recommendations MIXER SETUPINSTALLATION TIPS READ AND FOLLOW THESE INSTRUCTIONS WHEN SETTING UP THE MIXERMIXER SETUP SAFETY SHIELDSAUGER KNIVES REEL CROSS TUBESREAD AND FOLLOW THESE INSTRUCTIONS WHEN SETTING UP THE MIXER DRIVELINE SHEAR BOLTS 3136, 3142, 3150, 3160, 3170 & 3195 ONLYMIXER TEST RUN MIXER SETUPGENERAL SAFETYMIXER OPERATION MIXER OPERATION LIMITATIONSWARNINGS MIXING TIMEMIXER OPERATION MATERIAL THAT CAN BE LOADED DIRECTLY INTO THE MIXERMATERIALS REQUIRING PREPARATION HAY QUALITY2 LOAD HAY A LOAD PROCESSED HAY LOADING AND MIXINGMIXER OPERATION 1 LOAD COMMODITIESMIXER OPERATION FILL LEVELUNLOADING ELECTRONIC SCALES OPTIONSDOOR FLOW CONTROL PLATES ELECTRIC DOOR CONTROLINSPECT AND ADJUST INSPECTIONS AND ADJUSTMENTS3136 B0001 INSPECTION AND ADJUSTMENTS3150 - 3195 AND 3136 BEFORE S/N B0001 3150 TO 3195 AND 3136 BEFORE S/N B0001IMPORTANT! Read before operating mixer HAY MAXX SYSTEM ADJUSTMENTSINSPECTION AND ADJUSTMENTS Back to Table of ContentsKuhn Knight, Inc.27shields removed for illustrative purposes LUBRICATIONLUBRICATION LOCATIONS shields removed for illustrative purposes Back to Table of ContentsKuhn Knight, Inc.29LUBRICATION LUBRICATION LOCATIONSshields removed for illustrative purposes LUBRICATION LOCATIONS 3125 ANDBack to Table of Contents LUBRICATIONshields removed for illustrative purposes LUBRICATION LOCATIONS 3136, 3142, 3150, 3160, 3170 ANDBack to Table of ContentsKuhn Knight, Inc.31 LUBRICATIONBELTS SLIPPING SHEAR BOLT FAILS TROUBLE SHOOTINGPROBLEM EXCESSIVE POWER REQUIREMENTS WHEN RUNNING MIXERPROBLEM SEAL LEAKING ON INPUT SHAFT TROUBLE SHOOTINGPROBLEM MOTOR RUNS, BUT REEL AND AUGERS DO NOT TURN PROBLEM SEAL LEAKING ON UPPER AUGERPROBLEM SCALE HANGS UP, LOAD CELL ONLY TROUBLE SHOOTINGPROBLEM OIL LEAKING AROUND THE EDGES OF THE OIL BATH PROBLEM HYDRAULIC DOOR SYSTEM OPERATES ERRATICALLY3120 SPECIFICATIONS 3115 TOMODEL - STATIONARY 31153150 SPECIFICATIONS 3150 TOSAFETY MODEL - STATIONARY