Manuals / Kyocera / Computer Equipment / Printer

Kyocera FS-1020D manual List of Fonts, Internal Scalable and Bitmap Fonts and Kpdl Fonts

Models: FS-1020D

1 98

Download 98 pages 27.26 Kb

Page 60

List of Fonts

5.2List of Fonts

This section contains a full list of the printer’s internal fonts.

5.2.1Internal Scalable and Bitmap Fonts and KPDL Fonts

Font

number Font samples

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

5-3

Image 60

Kyocera FS-1020D manual List of Fonts, Internal Scalable and Bitmap Fonts and Kpdl Fonts

Contents

FS-1020D Regarding Tradenames Limited Warranty LicenseLimitation of Remedies GeneralTypeface Trademark Acknowledgement Agfa Japan License Agreement GuidelinesContents Fonts Appendix C Printer Specifications Introduction Guide to the Manuals DescriptionGuide to the Operation Guide Basic Operations Operator Panel Column of the table on the followingIndicators KeysReference Name Status Meaning Reference Name FunctionUnderstanding the Status Firmware versionInstallation Options Error LogSoftware Version Hardware InformationInterface Information KIR Test PatternMaintenance Toner Container Replacement Toner Container Replacement IntervalReplacement Replenishing Toner Bag and dispose of itTake the new toner container from the bag. Hold it with Container at the positions marked Push Here until you hear Cleaning the Printer Printer InteriorFront Cover Lift the process unit together with the toner container outNever stand the process unit on end RollerCleaner Home Position Next time you use the printerCorners of the top cover Troubleshooting General Guide for Troubleshooting Symptom Check Items Corrective ActionPrint Quality Problems Check the EcoPrint setting Toner indicatorTry setting the thin paper mode Adjust the corresponding custom paper typeCheck the paper size setting Check the file or programIndicators Maintenance Messages Indicator KM-NET for Clients display Corrective Action Resolution because there is not enoughThere is no cassette in the feeder, or Cassette is not inserted properlyErrors Requiring Service Personnel Attention Scanner pin-photo error 4200 errorEraser error 5300 error Waste toner reservoir is full 7990 error Controller check sum error F010 errorController RAM read/write error F020 error Engine ROM check sum error F050 error Error Messages Indicator KM-NET for Corrective Action Printer power is onMake sure to turn the printer power off before inserting This message appears when the printer is in the readyNormal Indicator Display Following displays appear during normal printer operationPaper Jam Removal Jam at the Face-down Tray and the Rear CoverJam at the Paper Cassette Jam at the DuplexerPull the paper cassette all the way out of the printer Jam Inside the Printer Jam at the MP Tray Normal paper running directionTo the MP tray. Instead, proceed to the next step Open the printer’s top and front covers RegistrationRegistration RollerMetalRollerMetal Paper Selection Paper Specifications SpecificationGeneral Guidelines Paper AvailabilitySelecting the Right Paper Condition of the PaperComposition Basis Weight Paper SizeSmoothness SizeMoisture Content Thickness CaliperPaper Grain Other Paper Properties Special Paper Transparency overhead projection filmCheck that printing quality is satisfactory Adhesive-Backed Labels Top sheet white bond paper Adhesive Carrier sheetPostcards EnvelopesThick Paper Colored PaperPreprinted Paper Recycled PaperMP Tray Paper Paper Weight Cassette Paper TypeFonts Internal Fonts List of Fonts Internal Scalable and Bitmap Fonts and Kpdl FontsList of Fonts List of Fonts Font Kpdl Fonts List of Fonts Appendix a Options Available Options Expansion Memory Installation Expansion memory should be installed only by a Kyocera MitaShall not be liable for damage due to improper installation Expansion memoryInstalling the Dimm Dimm to be usedInsert the Dimm into the Dimm socket so that the notches on Dimm align with the corresponding protrusions in the slotTesting the Expansion Memory Fasten it with the screwSetting the Printer Driver PropertiesMemory CompactFlash Card Again to restart the printerPush it in all the way Figure A-13Network Interface Card Interface cardRemoved in step Appendix B Host Computer Interface Auto default Parallel InterfaceNibble high NormalPin In/out Description 0V DCData 0 1 to Data 7 8 Pins 2 to Paper Empty PError PinReset nInit Pin Error* nFault PinSelect In nSelectIn Pin USB Interface Serial Interface Option SG Signal Ground Pin DTR Data Terminal Ready PinRS-232C Interface Voltage Levels RS-232C Protocol H1 Baud rateH2 Data bits H3 Stop bitsH5 Protocol logic H6 Buffer nearly-full thresholdH7 Buffer nearly-empty threshold H8 Received-data buffer sizeRS-232C Cable Connection Obtain a Suitable RS-232C CableDouble click on Communications Port \MODE LPT1=COM1 Appendix C Printer Specifications Printer Specifications Power requirements Power consumptionDimensions WeightGlossary Cassette mode First modeIEEE1284 Dpi dots per inchPrescribe commands MP trayParallel interface OfflineSleep mode StatusUSB Universal Serial Bus Index EcoPrint Glossary-2Emulation Glossary-2Envelope Index-3 2003 Is a trademark of Kyocera Corporation