Manuals / Kyocera / Computer Equipment / Printer

Kyocera FS-1020D manual RegistrationRegistration RollerMetalRollerMetal

Models: FS-1020D

1 98

Download 98 pages 27.26 Kb

Page 46

Paper Jam Removal

4

Use the following procedure that corresponds to the status of the

jammed paper, in order to remove that paper.

(A) If the leading edge of the jammed paper has been fed further into

the printer than the metal registration roller, remove the jammed

paper by its leading edge.

(B) If the paper has not been fed as far as the metal registration

roller, remove the jammed paper from the MP tray side.

(A)

(B)

RegistrationRegistration

Roller(Metal)Roller(Metal)

Figure 3-14

3-21

Image 46

Kyocera FS-1020D manual RegistrationRegistration RollerMetalRollerMetal

Contents

FS-1020D Regarding Tradenames Limitation of Remedies Limited WarrantyLicense GeneralTypeface Trademark Acknowledgement Agfa Japan License Agreement GuidelinesContents Fonts Appendix C Printer Specifications Introduction Guide to the Manuals DescriptionGuide to the Operation Guide Basic Operations Operator Panel Column of the table on the followingReference Name Status Meaning IndicatorsKeys Reference Name FunctionUnderstanding the Status Firmware versionSoftware Version Installation OptionsError Log Hardware InformationInterface Information KIR Test PatternMaintenance Toner Container Replacement Interval Toner Container ReplacementReplacement Replenishing Toner Bag and dispose of itTake the new toner container from the bag. Hold it with Container at the positions marked Push Here until you hear Front Cover Cleaning the PrinterPrinter Interior Lift the process unit together with the toner container outNever stand the process unit on end RollerCleaner Home Position Next time you use the printerCorners of the top cover Troubleshooting General Guide for Troubleshooting Symptom Check Items Corrective ActionPrint Quality Problems Try setting the thin paper mode Check the EcoPrint settingToner indicator Adjust the corresponding custom paper typeCheck the paper size setting Check the file or programIndicators Maintenance Messages There is no cassette in the feeder, or Indicator KM-NET for Clients display Corrective ActionResolution because there is not enough Cassette is not inserted properlyScanner pin-photo error 4200 error Errors Requiring Service Personnel AttentionEraser error 5300 error Controller check sum error F010 error Waste toner reservoir is full 7990 errorController RAM read/write error F020 error Engine ROM check sum error F050 error Error Messages Make sure to turn the printer power off before inserting Indicator KM-NET for Corrective ActionPrinter power is on This message appears when the printer is in the readyNormal Indicator Display Following displays appear during normal printer operationPaper Jam Removal Jam at the Face-down Tray and the Rear CoverJam at the Paper Cassette Jam at the DuplexerPull the paper cassette all the way out of the printer Jam Inside the Printer Normal paper running direction Jam at the MP TrayTo the MP tray. Instead, proceed to the next step Open the printer’s top and front covers RegistrationRegistration RollerMetalRollerMetal Paper Selection General Guidelines Paper SpecificationsSpecification Paper AvailabilityCondition of the Paper Selecting the Right PaperComposition Smoothness Basis WeightPaper Size SizeThickness Caliper Moisture ContentPaper Grain Other Paper Properties Transparency overhead projection film Special PaperCheck that printing quality is satisfactory Adhesive-Backed Labels Top sheet white bond paper Adhesive Carrier sheetPostcards EnvelopesPreprinted Paper Thick PaperColored Paper Recycled PaperMP Tray Paper Paper Weight Cassette Paper TypeFonts Internal Fonts List of Fonts Internal Scalable and Bitmap Fonts and Kpdl FontsList of Fonts List of Fonts Font Kpdl Fonts List of Fonts Appendix a Options Available Options Shall not be liable for damage due to improper installation Expansion Memory InstallationExpansion memory should be installed only by a Kyocera Mita Expansion memoryInstalling the Dimm Dimm to be usedInsert the Dimm into the Dimm socket so that the notches on Dimm align with the corresponding protrusions in the slotTesting the Expansion Memory Fasten it with the screwSetting the Printer Driver PropertiesMemory CompactFlash Card Again to restart the printerPush it in all the way Figure A-13Interface card Network Interface CardRemoved in step Appendix B Host Computer Interface Nibble high Auto defaultParallel Interface NormalPin In/out Description 0V DCReset nInit Pin Data 0 1 to Data 7 8 Pins 2 toPaper Empty PError Pin Error* nFault PinSelect In nSelectIn Pin USB Interface Serial Interface Option DTR Data Terminal Ready Pin SG Signal Ground PinRS-232C Interface Voltage Levels H2 Data bits RS-232C ProtocolH1 Baud rate H3 Stop bitsH7 Buffer nearly-empty threshold H5 Protocol logicH6 Buffer nearly-full threshold H8 Received-data buffer sizeRS-232C Cable Connection Obtain a Suitable RS-232C CableDouble click on Communications Port \MODE LPT1=COM1 Appendix C Printer Specifications Printer Specifications Dimensions Power requirementsPower consumption WeightGlossary IEEE1284 Cassette modeFirst mode Dpi dots per inchParallel interface Prescribe commandsMP tray OfflineStatus Sleep modeUSB Universal Serial Bus Index EcoPrint Glossary-2Emulation Glossary-2Envelope Index-3 2003 Is a trademark of Kyocera Corporation