Manuals / Kyocera / Computer Equipment / Printer

Kyocera FS-1020D manual Serial Interface Option

Models: FS-1020D

1 98

Download 98 pages 27.26 Kb

Page 81

Serial Interface (Option)

B.3 Serial Interface (Option)

Installing the optional serial interface board kit (IB-11) in the printer enables connection to a computer with an RS-232C standard serial interface.

B.3.1 RS-232C Interface

Interface Signals

The pins of the printer’s RS-232C interface connector carry the signals listed in Table B-3. The table also indicates whether each signal is incoming or outgoing with respect to the printer.

Pin	In/out	Signal	Description
1	-	FG	Frame ground

2	Out	TXD	Transmit Data

3	In	RXD	Receive Data

4	Out	RTS	Request To Send

5	In	CTS	Clear To Send

6	In	DSR	Data Set Ready

7	-	SG	Signal Ground

20	Out	DTR	Data Terminal Ready

Table B-3

Brief descriptions of the signals follow.

FG - Frame Ground - (Pin 1)

This pin is connected directly to the printer frame.

TXD - Transmit Data - (Pin 2)

This output carries asynchronous data sent by the printer to the computer.

It is used mainly in handshaking protocols.

RXD - Receive Data - (Pin 3)

This input carries serial asynchronous data sent by the computer to the printer.

RTS - Request To Send - (Pin 4)

This output is always held high (above 3 volts).

CTS - Clear To Send - (Pin 5)

DSR - Data Set Ready - (Pin 6)

Unused.

B-7

Image 81

Kyocera FS-1020D manual Serial Interface Option

Contents

FS-1020D Regarding Tradenames License Limited WarrantyLimitation of Remedies GeneralAgfa Japan License Agreement Guidelines Typeface Trademark AcknowledgementContents Fonts Appendix C Printer Specifications Introduction Description Guide to the ManualsGuide to the Operation Guide Basic Operations Column of the table on the following Operator PanelKeys IndicatorsReference Name Status Meaning Reference Name FunctionFirmware version Understanding the StatusError Log Installation OptionsSoftware Version Hardware InformationKIR Test Pattern Interface InformationMaintenance Toner Container Replacement Toner Container Replacement IntervalReplacement Bag and dispose of it Replenishing TonerTake the new toner container from the bag. Hold it with Container at the positions marked Push Here until you hear Printer Interior Cleaning the PrinterFront Cover Lift the process unit together with the toner container outRoller Never stand the process unit on endNext time you use the printer Cleaner Home PositionCorners of the top cover Troubleshooting Symptom Check Items Corrective Action General Guide for TroubleshootingPrint Quality Problems Toner indicator Check the EcoPrint settingTry setting the thin paper mode Adjust the corresponding custom paper typeCheck the file or program Check the paper size settingIndicators Maintenance Messages Resolution because there is not enough Indicator KM-NET for Clients display Corrective ActionThere is no cassette in the feeder, or Cassette is not inserted properlyErrors Requiring Service Personnel Attention Scanner pin-photo error 4200 errorEraser error 5300 error Waste toner reservoir is full 7990 error Controller check sum error F010 errorController RAM read/write error F020 error Engine ROM check sum error F050 error Error Messages Printer power is on Indicator KM-NET for Corrective ActionMake sure to turn the printer power off before inserting This message appears when the printer is in the readyFollowing displays appear during normal printer operation Normal Indicator DisplayJam at the Face-down Tray and the Rear Cover Paper Jam RemovalJam at the Duplexer Jam at the Paper CassettePull the paper cassette all the way out of the printer Jam Inside the Printer Jam at the MP Tray Normal paper running directionTo the MP tray. Instead, proceed to the next step Open the printer’s top and front covers RegistrationRegistration RollerMetalRollerMetal Paper Selection Specification Paper SpecificationsGeneral Guidelines Paper AvailabilitySelecting the Right Paper Condition of the PaperComposition Paper Size Basis WeightSmoothness SizeMoisture Content Thickness CaliperPaper Grain Other Paper Properties Special Paper Transparency overhead projection filmCheck that printing quality is satisfactory Top sheet white bond paper Adhesive Carrier sheet Adhesive-Backed LabelsEnvelopes PostcardsColored Paper Thick PaperPreprinted Paper Recycled PaperPaper Type MP Tray Paper Paper Weight CassetteFonts Internal Fonts Internal Scalable and Bitmap Fonts and Kpdl Fonts List of FontsList of Fonts List of Fonts Font Kpdl Fonts List of Fonts Appendix a Options Available Options Expansion memory should be installed only by a Kyocera Mita Expansion Memory InstallationShall not be liable for damage due to improper installation Expansion memoryDimm to be used Installing the DimmDimm align with the corresponding protrusions in the slot Insert the Dimm into the Dimm socket so that the notches onFasten it with the screw Testing the Expansion MemoryProperties Setting the Printer DriverAgain to restart the printer Memory CompactFlash CardFigure A-13 Push it in all the wayNetwork Interface Card Interface cardRemoved in step Appendix B Host Computer Interface Parallel Interface Auto defaultNibble high Normal0V DC Pin In/out DescriptionPaper Empty PError Pin Data 0 1 to Data 7 8 Pins 2 toReset nInit Pin Error* nFault PinSelect In nSelectIn Pin USB Interface Serial Interface Option SG Signal Ground Pin DTR Data Terminal Ready PinRS-232C Interface Voltage Levels H1 Baud rate RS-232C ProtocolH2 Data bits H3 Stop bitsH6 Buffer nearly-full threshold H5 Protocol logicH7 Buffer nearly-empty threshold H8 Received-data buffer sizeObtain a Suitable RS-232C Cable RS-232C Cable ConnectionDouble click on Communications Port \MODE LPT1=COM1 Appendix C Printer Specifications Printer Specifications Power consumption Power requirementsDimensions WeightGlossary First mode Cassette modeIEEE1284 Dpi dots per inchMP tray Prescribe commandsParallel interface OfflineSleep mode StatusUSB Universal Serial Bus Index EcoPrint Glossary-2Emulation Glossary-2Envelope Index-3 2003 Is a trademark of Kyocera Corporation