Manuals / Kyocera / Computer Equipment / Printer

Kyocera FS-1020D manual Dimm to be used, Installing the Dimm

Models: FS-1020D

1 98

Download 98 pages 27.26 Kb

Page 68

Expansion Memory Installation

DIMM to be used

Contact your Kyocera Mita dealer for information on purchasing the DIMM that are best suited for use with this printer.

Either an 8 MB, 16 MB, 32 MB, 64 MB, 128 MB, or 256 MB DIMM can be used for memory expansion.

Installing the DIMM

Insert the DIMM into the socket as follows:

1	Turn the printer’s power off, then unplug the printer’s power cable
1	and disconnect the printer from the host computer.
2	Remove the screw from the rear of the printer.

Figure A-6

3 Remove the side cover as shown in the figure.

Side Cover

Figure A-7

A-4

Image 68

Kyocera FS-1020D manual Dimm to be used, Installing the Dimm

Contents

FS-1020D Regarding Tradenames Limited Warranty LicenseLimitation of Remedies GeneralTypeface Trademark Acknowledgement Agfa Japan License Agreement GuidelinesContents Fonts Appendix C Printer Specifications Introduction Guide to the Manuals DescriptionGuide to the Operation Guide Basic Operations Operator Panel Column of the table on the followingIndicators KeysReference Name Status Meaning Reference Name FunctionUnderstanding the Status Firmware versionInstallation Options Error LogSoftware Version Hardware InformationInterface Information KIR Test PatternMaintenance Replacement Toner Container ReplacementToner Container Replacement Interval Replenishing Toner Bag and dispose of itTake the new toner container from the bag. Hold it with Container at the positions marked Push Here until you hear Cleaning the Printer Printer InteriorFront Cover Lift the process unit together with the toner container outNever stand the process unit on end RollerCleaner Home Position Next time you use the printerCorners of the top cover Troubleshooting General Guide for Troubleshooting Symptom Check Items Corrective ActionPrint Quality Problems Check the EcoPrint setting Toner indicatorTry setting the thin paper mode Adjust the corresponding custom paper typeCheck the paper size setting Check the file or programIndicators Maintenance Messages Indicator KM-NET for Clients display Corrective Action Resolution because there is not enoughThere is no cassette in the feeder, or Cassette is not inserted properlyEraser error 5300 error Errors Requiring Service Personnel AttentionScanner pin-photo error 4200 error Controller RAM read/write error F020 error Waste toner reservoir is full 7990 errorController check sum error F010 error Engine ROM check sum error F050 error Error Messages Indicator KM-NET for Corrective Action Printer power is onMake sure to turn the printer power off before inserting This message appears when the printer is in the readyNormal Indicator Display Following displays appear during normal printer operationPaper Jam Removal Jam at the Face-down Tray and the Rear CoverJam at the Paper Cassette Jam at the DuplexerPull the paper cassette all the way out of the printer Jam Inside the Printer To the MP tray. Instead, proceed to the next step Jam at the MP TrayNormal paper running direction Open the printer’s top and front covers RegistrationRegistration RollerMetalRollerMetal Paper Selection Paper Specifications SpecificationGeneral Guidelines Paper AvailabilityComposition Selecting the Right PaperCondition of the Paper Basis Weight Paper SizeSmoothness SizePaper Grain Moisture ContentThickness Caliper Other Paper Properties Check that printing quality is satisfactory Special PaperTransparency overhead projection film Adhesive-Backed Labels Top sheet white bond paper Adhesive Carrier sheetPostcards EnvelopesThick Paper Colored PaperPreprinted Paper Recycled PaperMP Tray Paper Paper Weight Cassette Paper TypeFonts Internal Fonts List of Fonts Internal Scalable and Bitmap Fonts and Kpdl FontsList of Fonts List of Fonts Font Kpdl Fonts List of Fonts Appendix a Options Available Options Expansion Memory Installation Expansion memory should be installed only by a Kyocera MitaShall not be liable for damage due to improper installation Expansion memoryInstalling the Dimm Dimm to be usedInsert the Dimm into the Dimm socket so that the notches on Dimm align with the corresponding protrusions in the slotTesting the Expansion Memory Fasten it with the screwSetting the Printer Driver PropertiesMemory CompactFlash Card Again to restart the printerPush it in all the way Figure A-13Removed in step Network Interface CardInterface card Appendix B Host Computer Interface Auto default Parallel InterfaceNibble high NormalPin In/out Description 0V DCData 0 1 to Data 7 8 Pins 2 to Paper Empty PError PinReset nInit Pin Error* nFault PinSelect In nSelectIn Pin USB Interface Serial Interface Option RS-232C Interface Voltage Levels SG Signal Ground PinDTR Data Terminal Ready Pin RS-232C Protocol H1 Baud rateH2 Data bits H3 Stop bitsH5 Protocol logic H6 Buffer nearly-full thresholdH7 Buffer nearly-empty threshold H8 Received-data buffer sizeRS-232C Cable Connection Obtain a Suitable RS-232C CableDouble click on Communications Port \MODE LPT1=COM1 Appendix C Printer Specifications Printer Specifications Power requirements Power consumptionDimensions WeightGlossary Cassette mode First modeIEEE1284 Dpi dots per inchPrescribe commands MP trayParallel interface OfflineUSB Universal Serial Bus Sleep modeStatus Index EcoPrint Glossary-2Emulation Glossary-2Envelope Index-3 2003 Is a trademark of Kyocera Corporation