Manuals / Kyocera / Computer Equipment / Printer

Kyocera FS-1020D manual Replenishing Toner, Bag and dispose of it

Models: FS-1020D

1 98

Download 98 pages 27.26 Kb

Page 19

Toner Container Replacement

2.1.2Replenishing Toner

1 Open the printer’s top cover.

Top Cover

	Figure 2-1
2	Pull lock lever #1 to the release (UNLOCK) position, then pull lock
2	lever #2 to the release (right) position.

Lock Lever #2

Lock Lever #1

	Figure 2-2
3	Gently remove the old toner container. Put it in the supplied plastic
3	bag and dispose of it.

Plastic Bag

Figure 2-3

2-3

Image 19

Kyocera FS-1020D manual Replenishing Toner, Bag and dispose of it

Contents

FS-1020D Regarding Tradenames General Limited WarrantyLicense Limitation of RemediesAgfa Japan License Agreement Guidelines Typeface Trademark AcknowledgementContents Fonts Appendix C Printer Specifications Introduction Description Guide to the ManualsGuide to the Operation Guide Basic Operations Column of the table on the following Operator PanelReference Name Function IndicatorsKeys Reference Name Status MeaningFirmware version Understanding the StatusHardware Information Installation OptionsError Log Software VersionKIR Test Pattern Interface InformationMaintenance Toner Container Replacement Interval Toner Container ReplacementReplacement Bag and dispose of it Replenishing TonerTake the new toner container from the bag. Hold it with Container at the positions marked Push Here until you hear Lift the process unit together with the toner container out Cleaning the PrinterPrinter Interior Front CoverRoller Never stand the process unit on endNext time you use the printer Cleaner Home PositionCorners of the top cover Troubleshooting Symptom Check Items Corrective Action General Guide for TroubleshootingPrint Quality Problems Adjust the corresponding custom paper type Check the EcoPrint settingToner indicator Try setting the thin paper modeCheck the file or program Check the paper size settingIndicators Maintenance Messages Cassette is not inserted properly Indicator KM-NET for Clients display Corrective ActionResolution because there is not enough There is no cassette in the feeder, orScanner pin-photo error 4200 error Errors Requiring Service Personnel AttentionEraser error 5300 error Controller check sum error F010 error Waste toner reservoir is full 7990 errorController RAM read/write error F020 error Engine ROM check sum error F050 error Error Messages This message appears when the printer is in the ready Indicator KM-NET for Corrective ActionPrinter power is on Make sure to turn the printer power off before insertingFollowing displays appear during normal printer operation Normal Indicator DisplayJam at the Face-down Tray and the Rear Cover Paper Jam RemovalJam at the Duplexer Jam at the Paper CassettePull the paper cassette all the way out of the printer Jam Inside the Printer Normal paper running direction Jam at the MP TrayTo the MP tray. Instead, proceed to the next step Open the printer’s top and front covers RegistrationRegistration RollerMetalRollerMetal Paper Selection Paper Availability Paper SpecificationsSpecification General GuidelinesCondition of the Paper Selecting the Right PaperComposition Size Basis WeightPaper Size SmoothnessThickness Caliper Moisture ContentPaper Grain Other Paper Properties Transparency overhead projection film Special PaperCheck that printing quality is satisfactory Top sheet white bond paper Adhesive Carrier sheet Adhesive-Backed LabelsEnvelopes PostcardsRecycled Paper Thick PaperColored Paper Preprinted PaperPaper Type MP Tray Paper Paper Weight CassetteFonts Internal Fonts Internal Scalable and Bitmap Fonts and Kpdl Fonts List of FontsList of Fonts List of Fonts Font Kpdl Fonts List of Fonts Appendix a Options Available Options Expansion memory Expansion Memory InstallationExpansion memory should be installed only by a Kyocera Mita Shall not be liable for damage due to improper installationDimm to be used Installing the DimmDimm align with the corresponding protrusions in the slot Insert the Dimm into the Dimm socket so that the notches onFasten it with the screw Testing the Expansion MemoryProperties Setting the Printer DriverAgain to restart the printer Memory CompactFlash CardFigure A-13 Push it in all the wayInterface card Network Interface CardRemoved in step Appendix B Host Computer Interface Normal Auto defaultParallel Interface Nibble high0V DC Pin In/out DescriptionError* nFault Pin Data 0 1 to Data 7 8 Pins 2 toPaper Empty PError Pin Reset nInit PinSelect In nSelectIn Pin USB Interface Serial Interface Option DTR Data Terminal Ready Pin SG Signal Ground PinRS-232C Interface Voltage Levels H3 Stop bits RS-232C ProtocolH1 Baud rate H2 Data bitsH8 Received-data buffer size H5 Protocol logicH6 Buffer nearly-full threshold H7 Buffer nearly-empty thresholdObtain a Suitable RS-232C Cable RS-232C Cable ConnectionDouble click on Communications Port \MODE LPT1=COM1 Appendix C Printer Specifications Printer Specifications Weight Power requirementsPower consumption DimensionsGlossary Dpi dots per inch Cassette modeFirst mode IEEE1284Offline Prescribe commandsMP tray Parallel interfaceStatus Sleep modeUSB Universal Serial Bus Index EcoPrint Glossary-2Emulation Glossary-2Envelope Index-3 2003 Is a trademark of Kyocera Corporation