Manuals / Lancom Systems / Computer Equipment / Network Router

Lancom Systems 7111 VPN, 8011 VPN manual

Models: 8011 VPN 7111 VPN

1 77

Download 77 pages 46.77 Kb

Page 25

WAN – connect the WAN port with the included connector cable (dark blue plug) e. g. with the ethernet port of a DSL modem or of a cable modem.

LANCOM 7111 VPN – LANCOM 8011 VPN

Chapter 2: Installation

LAN – connect the LANCOM router to your LAN or to an individual PC. For that purpose, plug the included network cable (green plugs) into the LAN connector of the device and the other end into a free network connect- ing socket of your local network, into a free socket of a hub/switch or into the network socket of an individual PC.

The LAN connector identifies automatically the transfer rate (10/100 Mbps) of the connected network device (autosensing). A parallel connec- tion of devices with different speeds and types is possible.

You should never have more than one unconfigured LANCOM router in a network segment at any given time. All unconfigured LANCOM router devices use the same IP address (with the final digits '254'), which would result in an address conflict. To avoid problems, always configure multiple LANCOM router devices one at a time, immediately assigning each device a unique IP address (one that does not end with '254').

WAN – connect the WAN port with the included connector cable (dark blue plug) e. g. with the ethernet port of a DSL modem or of a cable modem.

ISDN – to connect the LANCOM router to the ISDN, plug one end of the supplied ISDN connector cable (light blue plugs) in the ISDN/S0 port of the router and the other end into an ISDN/S0 multi-device mode or point- to-point mode connection.

Configuration port – you may optionally connect the router directly to the serial port (RS-232, V.24) of a PC. Use the cable supplied for this pur- pose. Connect the configuration port of the LANCOM with a free serial port of the PC.

Connect to power – Connect socket of the unit to a power supply using the included power adapter and switch it on .

With the LANCOM 7111 VPN only use the included power supply unit! Using an unsuitable power supply unit may cause damage or injury.

Operational? – After a short device self-test the Power LED will be per- manently lit. Green LAN LEDs indicate the LAN sockets that have function- ing connections.

EN

25

Image 25

Lancom Systems 7111 VPN, 8011 VPN manual

Contents

LANCOM 7111 VPN LANCOM 8011 VPN 2004 LANCOM Systems GmbH, Wuerselen Germany. All rights reserved Preface Security settingsModel variants User manual and reference manualThis documentation was compiled … Notes symbolsinfo@lancom.de 2 Installation Contents3 Basic configuration 4 Setting up Internet access5 Linking two networks Providing dial-up access7 Sending faxes with LANCAPI Security settingsAppendix 9 Troubleshooting1.1 Which use does VPN offer? 1 IntroductionChapter 1 Introduction A subsidiary is connected to the LAN, typically using a leased line Conventional network infrastructureAccess Service - RAS Chapter 1 IntroductionNetworking via the Internet Further important features of the Firewall are Intrusion Detection 1.2 FirewallDenial-of-Service Protection 1.3 What does a router do?Quality-of-Service / Traffic management LANCOM CD1.3.1 Bridgehead to the WAN Internet access for a LAN e.g. via DSL or ISDN1.3.2 Areas of deployment for routers LAN to LAN coupling via VPN or ISDN1.4 What can your LANCOM router do? Remote access to the company network via VPN or ISDNLANCOM LANCOMWAN connection LAN connectionConfiguration Quality of ServiceLANCOM Optional software extensions2.1 Package contents 2 Installation2.2 System preconditions 2.3.1 Status displays 2.3 Introducing LANCOM routerFront side Meanings of the LEDsand the LED remains lit green Chapter 2 InstallationThe Online LED indicates the overall status of all WAN ports inverse flashingChapter 2 Installation Flashing Power LED but no connection?Completely deactivate the lock that has been triggered set limit to LANCOMNot connected or no S0 voltage no error message Chapter 2 InstallationConnection status of the WAN connection Data traffic via the WAN connectionLCD display 2.3.2 The back of the unit 2.4 Hardware installationWAN - connect the WAN port with the included connector cable dark blue plug e. g. with the ethernet port of a DSL modem or of a cable modem 2.5.1 Starting LANCOM setup 2.5 Software installation2.5.2 Which software should you install? 3.1.1 TCP/IP settings 3 Basic configuration3.1 Which information is necessary? Configure manually nevertheless? New LAN-fully automatic configuration possibleInformation required for manual TCP/IP configuration IP address and netmask for the LANCOM router3.1.3 Settings for the DSL connection 3.1.2 Configuration protection3.1.4 Settings for the ISDN connection Enable DHCP server?LANconfig 3.2 Instructions for LANconfig3.1.5 Connect charge protection Chapter 3 Basic configurationComplete the configuration with Finish Network without DHCP server 3.3 Instructions for WEBconfigChapter 3 Basic configuration Network with DHCP server Starting the wizards in WEBconfigPage Entering the password in the web browser IP address assignment via the LANCOM router default 3.4 TCP/IP settings to workstation PCsManual IP address assignment IP address assignment via a separate DHCP serverChapter 3 Basic configuration Does the setup wizard know your Internet provider? 4 Setting up Internet accessAdditional information for unknown Internet providers Chapter 4 Setting up Internet accessISDN - dial-in number User name and password Additional connection optionsChapter 4 Setting up Internet access Dynamic channel bundling ISDN only4.2 Instructions for WEBconfig 4.1 Instructions for LANconfigLANconfig Quick access to the setup wizards 5 Linking two networks Always configure both sidesSecurity aspects 5.1.1 General information 5.1 What information is necessary?The name of the remote station is needed for its identification Chapter 5 Linking two networks 5.1.2 Settings for the TCP/IP routerNetmask DNS access to the remote LAN 5.1.3 Settings for the IPX routerExtranet VPN 5.1.4 Settings for NetBIOS routing 5.3 Instructions for WEBconfig 5.2 Instructions for LANconfigPing - quick testing for TCP/IP connections 6.1 Which information is required? 6 Providing dial-up accessSecurity aspects The ISDN calling line identity CLI 6.1.1 General information6.1.3 Settings for IPX 6.1.2 Settings for TCP/IPChapter 6 Providing dial- up access 6.1.4 Settings for NetBIOS routingUser SAMPLE 6.2.1 Dial-up via VPN 6.2 Settings for the dial-in computer6.2.2 Dial-up via ISDN 6.4 Instructions for WEBconfig 6.3 Instructions for LANconfigFrom the main menu, launch the Connect two local networks wizard Chapter 6 Providing dial- up accessChapter 7 Sending faxes with LANCAPI 7 Sending faxes with LANCAPIChapter 7 Sending faxes with LANCAPI 7.1 Installation of the LANCOM CAPI fax modemSelect the option Printers and Faxes from the control panel 7.2 Installation of the MS Windows fax serviceChapter 7 Sending faxes with LANCAPI 7.3 Sending a fax 7.3.2 Send a fax with the MS Windows fax service7.3.1 Send a fax with any given office application Chapter 7 Sending faxes with LANCAPI LANCOM 7111 VPN - LANCOM 8011 VPN8.1 The security settings wizard 8 Security settings8.1.1 Wizard for LANconfig 8.2.1 Wizard for LANconfig 8.1.2 Wizard for WEBconfig8.2 The firewall wizard 8.2.2 Configuration under WEBconfig 8.3 The security checklistRules Have you permitted remote configuration? Have you assigned a password for the configuration?Have you activated the Firewall? Do you make use of a ’Deny All’ Firewall strategy?Have you closed critical ports with filters? Have you excluded certain stations from access to the router?Is your saved LANCOM router configuration stored in a safe place? Chapter 8 Security settingsProblems with the cabling? 9 Troubleshooting9.1 No WAN connection is established 9.2 DSL data transfer is slow9.3 Unwanted connections under Windows XP 9.4 Cable testingIncreasing the TCP/IP window size under Windows LAN statisticsChange then to menu item Expert configuration Status LAN statis 10 Appendix 10.1 Performance data and specificationsLANCOM 7111 VPN LANCOM 8011 VPNLANCOM 8011 VPN LANCOM 7111 VPNChapter 10 Appendix 10.2.1 DSL interface 10.2 Contact assignment10.2.2 ISDN-S0 interface Connector10.3 CE declaration of conformity 10.2.4 Configuration interface Outband10.2.3 Ethernet interfaces 10/100Base-T ConnectorNumerics IndexBasic configuration Authentication data12, 14, 16 see status displaysSetting up access to the Internet Enable software compressionVirtual Private Network VPN