Land Pride SC2660 Motor And Hose Assembly, SC2672 Motor And Hose Assembly, Table of Contents

Table of Contents

Section 1: Assembly & Set-up

Land Pride

SC2660 Motor And Hose Assembly

Your Skid Steer Rotary Cutter is factory supplied with one of three motors mounted to the deck. Make sure you check GPM rating on the hydraulic motor decal to verify if it matches your Skid Steer’s GPM rating. Skip assembly instructions below if the motor GPM rating matches your Skid Steer.

See “Motor and Hose Assembly” on page 21 to properly select a motor that matches your Skid Steer.

Refer to Figure 1-2:

1.Remove fasteners (#1, 2, 3 & 4). Keep fasteners for reassembly of new motor.

2.Remove existing motor and hose assembly (#5). Clean old gasket material (#6) from gearbox flange (#7).

3.Place new gasket (#6) onto gearbox flange (#7).

4.Gently lower new motor and hose assembly (#5) onto gasket (#6) with hoses extending towards the hitch plate.

5.Secure hydraulic motor assembly with the four existing 1/2"-13 x 2 1/4" lg. GR 5 hex head bolts (#1), flat washers (#4), lock washers (#3) and 1/2"-13 hex huts (#2). Tighten nuts to the correct torque. See “Torque Values Chart” on page 31.

Decal Location

Stating Motor

GPM Rating

24545

SC2660 Motor and hose Assembly

Figure 1-2

SC2672 Motor And Hose Assembly

Your Skid Steer Rotary Cutter is factory supplied with one of three motors mounted to the deck. Make sure you check GPM rating on the hydraulic motor decal to verify if it matches your Skid Steer’s GPM rating. Skip assembly instructions below if the motor GPM rating matches your Skid Steer.

See “Motor and Hose Assembly” on page 21 to properly select a motor that matches your Skid Steer.

Refer to Figure 1-3:

1.Remove fasteners (#9 & #10) and coupling

guard (#8). Keep fasteners and coupling guard for reassembly of new motor.

1.Remove fasteners (#1, 2, 3 & 4). Keep fasteners for reassembly of new motor.

2.Remove existing motor and hose assembly (#5). Clean old gasket material (#6) from mounting flange (#7).

3.Place new gasket (#6) onto mounting flange (#7).

4.Gently slide new motor and hose assembly (#5) onto coupling (#12) with hoses extending towards the hitch plate.

5.Secure hydraulic motor assembly with the four existing 1/2"-13 x 2 1/4" lg. GR 5 hex head bolts (#1), flat washers (#4), lock washers (#3) and 1/2"-13 hex huts (#2). Tighten nuts to the correct torque. See “Torque Values Chart” on page 31.

6.Reattach coupling guard (#8) with 5/16" spring lock washers (#10) and 5/16"-18 x 3/4" GR5 hex head cap screws (#9). Tighten nuts to correct torque.

Decal Location Stating
Motor GPM Rating	25732

SC2672 Motor and hose Assembly

Figure 1-3

SC2672 Vent Plug With Dipstick

IMPORTANT: Ref. Figure 1-4. A solid plug is shipped with the gearbox to prevent loss of oil during shipping and handling. Before operating the cutter, this plug must be replaced with the vent plug and dipstick included with this manual.

Vented Plug

With DipstickOil Level

Plug

DO NOT

OVERFILL

20822

Figure 1-4

10 SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M 1/07/09