Land Pride

Section 4 Maintenance and Lubrication

Belt Replacement

Refer to Figure 4-10and Figure 4-11:

Replace belts which show signs of severe cuts, tears, excessive weather checking and cracking or burns caused by slipping. Slight raveling of belt covering does not indicate failure, trim ravelings with a sharp knife.

Inspect the belt pulley grooves and flanges for wear. A new belt, or one in good condition, should never run against the bottom of the groove. Replace the pulley when this is the case, otherwise belt will lose power and slip excessively.

Never pry a belt to get it on a pulley as this will cut or damage the fibers of the belt covering.

Keep oil and grease away from belts, and never use belt dressings. Any of these will destroy the belt composition in a very short time.

Mower Blade Maintenance

Lift Jack Option

For easier blade maintenance a lift jack can be purchased from your Land Pride Dealer and easily assembled to your mower. Refer to Figure 4-12.

 

Lift Jack

19912

Figure 4-12

 

 

Check the mower blades daily, they are the key to power efficiency and well groomed turf. Keep them sharp, a dull blade will tear rather than cut the grass, leaving a brown ragged top on the grass within a few hours. A dull blade also requires more power from the engine.

Replace any blade which is bent, cracked or broken.

Never attempt to straighten a bent blade by heating, or weld a cracked or broken blade as the blade may break and cause serious injury.

!DANGER!

Never work with blades while engine is running or deck clutch is engaged. Always place deck clutch in the disengaged position, place control levers in park position and turn engine off. Block up mower when you must work under it. Do not use jack as blocks. Jack is for lifting only. Separate blocks must be used prior to servicing under mower. Wear gloves when handling blades. Always check for blade damage if mower strikes rock, branch or other foreign object during mowing!

Mower Blade Removal

Use a 3/4" wrench to remove the 1/2" cap screw holding blade to spindle saddle from underneath.

Sharpen the blades on a grinder following pattern as shown in Figure 4-13.Touch-up sharpening can be done with a file.

19074

Resharpening Pattern

Do not sharpen to original pattern (below).

It is easier to get a straight cutting edge following the resharpening pattern shown above.

19075

Blade Resharpening Original Edge

Figure 4-13

Check the blades for balance following grinding. A commercial balancing tool is available through most hardware supply stores, or balancing can be done by placing the blade on an inverted line punch or 1/2" bolt. Blade should not lean or tilt. Spin the blade slowly, blade should not wobble. If blade is out of balance, true it up before reinstalling.

Lay the blade on a flat surface and check for distortion. Replace any distorted blade. Refer Figure 4-14and Figure 4-15on next page.

38 Z52®, Z60® & Z72® Zero Turning Radius Mowers Accu-Z 356-005M

03/11/03

Page 40
Image 40
Land Pride Z52, Z60 Belt Replacement, Mower Blade Maintenance, Mower Blade Removal, Lift Jack Option, Resharpening Pattern

Z60, Z52, Z52 , Z60, Z72 specifications

Land Pride is a recognized leader in the manufacturing of high-quality outdoor equipment, particularly known for their commercial mowers. Among their lineup, models like the ZXT54, ZT60, Z52, Z44, and ZT72 stand out for their commitment to performance, durability, and ease of use. These zero-turn mowers are designed to tackle a variety of mowing tasks, making them ideal for both residential and commercial applications.

The Land Pride ZXT54 model features a 54-inch cutting deck, which provides ample width for efficient mowing. Its powerful engine, designed for reliability and performance, ensures that grass can be cut cleanly and quickly, even in challenging conditions. Users appreciate the intuitive controls that allow for precise maneuvering, making it easy to navigate around obstacles like trees and flower beds. The ZXT54 also includes features such as a comfortable seat and ergonomic handle grips, enhancing operator comfort during extended use.

Moving to the ZT60, this model takes it a step further with a 60-inch cutting deck. This increased size makes it ideal for large lawns or commercial properties, allowing more area to be covered in less time. The ZT60 is equipped with advanced mowing technology that ensures an even cut and a clean finish. An adjustable cutting height gives users the flexibility to adapt to different grass types and growth conditions.

The Z52 model is another solid option for users looking for a balance between power and maneuverability. With a 52-inch cutting deck, this model is favored for its agility in tighter spaces while still providing a robust mowing performance. The Z52 boasts some of the latest technological advancements, including a heavy-duty chassis and an efficient engine that prolongs work time and reduces wear.

For smaller properties, the Z44 model shines with its 44-inch deck, making it perfect for navigating narrow spaces without compromising on cutting performance. Its compact size does not sacrifice power, as it is outfitted with a capable engine that can handle various grass types while providing a reliable performance.

Finally, the ZT72 model, with its impressive 72-inch cutting deck, is engineered specifically for extensive commercial use. It is built to withstand demanding conditions, featuring heavy-duty components that ensure longevity. The ZT72 also includes advanced features like an enhanced mulching option and a robust suspension system, providing a smooth ride over uneven terrain.

In summary, the Land Pride ZXT54, ZT60, Z52, Z44, and ZT72 models each offer unique features tailored to meet the varying needs of users. Whether for residential use or commercial applications, these mowers deliver power, efficiency, and unmatched comfort, ensuring that mowing tasks are completed effectively and with ease.