Land Pride Z52 , Z60, Z72 manual Deck Cutting Height Adjustment, Height Adjusting Stop 1/4” Plate

Land Pride

Section 3 Adjustments

10.Jam both nuts against the block.

11.Push or pull on the deck lift foot pedal until the chain on the left front just becomes tight, making sure that the deck stays tight against the 3" block.

12.While keeping the chain tight, tighten the nuts against the deck lift block on the height indicator rod. See Figure 3-19.

13.Go to the right front of the mower.

14.Loosen the 5/16" jam nut on the adjuster lift chain (Figure 3-18),and back the adjuster bolt out to allow the adjuster to move up and down freely.

15.Be sure that adjuster is free to move up and down.

16.Tighten the adjuster bolt until the chain just becomes tight, making sure that the deck stays tight against the 3" block.

17.Tighten the adjuster bolt jam nut to prevent the adjuster bolt from moving. See Figure 3-18.

18.Tighten the hardware holding the chain and adjuster onto the deck lift arm.

19.Go to the right rear of the mower.

20.Make sure that there is still slack in the chain. If not, loosen the two nuts on the block holding the threaded rod until there is slack in the deck lift chain.

See Figure 3-17.

21.Tighten the appropriate nut until the chain just becomes tight, making sure that the deck stays tight against the 3" block.

22.Tighten the other nut on the opposite side of the block, and jam them tightly together against the block.

23.Go to the left rear of the mower.

24.Make sure that there is still slack in the chain. If not, loosen the two nuts on the block holding the threaded rod until there is slack in the deck lift chain.

See Figure 3-16.

25.Tighten the appropriate nut until the chain just becomes tight.

26.Tighten the other nut on the opposite side of the block, and jam them tightly together against the block.

27.Compress the deck lift assist springs so that there is 1” of space between the front nut and on the spring and the rear nut on the deck lift block (Figure 3-20). Typical both sides.

28.When completed, all chains will be tight, and deck cutting height will be set to the deck height indicator.

Deck Cutting Height Adjustment

Deck height is adjustable from 1” to 5” in 1/4” increments. The holes in the height adjusting bar are spaced at 1/2” intervals. By turning the height adjusting stop around, 1/4” increments can be attained due to the 1/4” plate that is part of the stop. Refer to Figure 3-21.

Height Adjusting

Stop

1/4” Plate

Deck Cutting Height	19089
Figure 3-21

EXAMPLE: When the height adjusting stop is placed in the 1” hole, with the 1/4” plate facing to the front of the unit, the cutting height is at 1”. When the height adjusting stop is placed in the 1” hole, with the 1/4” plate on the operator’s side of the hole, the cutting height is at 1 1/4”.

When the height adjusting stop is placed in one of the holes, with the 1/4” plate on the operator’s side of the hole, the deck height will be set at one of the following: 1 1/4”, 1 3/4”, 2 1/4”, 2 3/4”, 3 1/4”, 3 3/4”, 4 1/4” or 4 3/4”.

When the height adjusting stop is placed in one of the holes, with the 1/4” plate facing to the front of the unit, the deck height will be set at one of the following: 1”, 1 1/2”, 2”, 2 1/2”, 3”, 3 1/2”, 4”, 4 1/2” or 5”.

The notch located at the rear of the right height adjusting bar is to used when the deck is placed in the transport mode.

28 Z52®, Z60® & Z72® Zero Turning Radius Mowers Accu-Z 356-005M 03/11/03