ENGLISH
5
Scan Modes
Scanning is a Dealer programmable feature that allows you to monitor a number of channels. Your radio communications Dealer will help you define a scanning mode and your channel “scan list”.
Once the scan list has been established, initiate scan by pressing the SCAN button. The SCAN icon will show in the lower right corner of the display to confirm radio scanning.
Normal Channel Scan
If a conversation is detected on any of the channels in the scan list, the radio will stop on that channel and you will be able to hear the conversation. In normal scan, you can transmit on that active channel during the programmable scan delay time. (The scan delay time is the amount of time the radio will stay on that channel once activity has ceased. Dealer programmable, 4 - 7 seconds is typical).
The radio will resume scanning once the scan delay time has expired, and will continue to scan until scanning stops by pressing the SCAN button. In scan mode, if radio power is turned off and on, the radio will return to the scan mode until scanning stops by pressing the SCAN button.
Priority Scan TX
A single channel may be programmed as the “Priority” channel. Priority channel activity takes precedence over all other conversations. During the scan mode, if a
Priority Lookback Scan
A single channel may be programmed as the “Priority” channel. The radio will constantly monitor this channel while scanning and when stopped on an active channel. If a call is detected on the Priority channel during a conversation, the radio will automatically move to, and remain on, the Priority channel. Priority channel activity takes precedence over all other conversations.
Priority Select Scan
A selected channel becomes the “Priority” channel. As you change the channel, that channel’s frequency will become your new Priority channel. Priority channel activity takes precedence over all other conversations.
Nuisance Delete
During receiving a signal or scan delay time, if the MON (monitor) button is pressed, the current receiving channel is deleted in scan list and is no longer scanned. When the power is turned off and on, the deleted channel is restored to the scan list.
Busy Channel Lockout
When the RX signal is being received, the radio’s transmitter is disabled.
Marked Idle
When used in conjunction with Busy Channel Lockout (BCLO), the radio will allow a transmission if the correct tone is present with the received signal.
TX Delay
The transmission will remain active for approximately 180 milliseconds even though the
The purpose of the
When
Press the
Each channel can be programmed with
Weather Alert Detect(1050 Hz Detect)
Checks for the 1050 Hz of Weather Alert tone Signal issued by the National Weather Service. Your radio will look back to the last used weather channel every 5 seconds. If the 1050 Hz is detected, WX ALERT will blink on screen with alert alarm, then change to WX mode. To stop WX ALERT blinking and alarm, press any bution.
VOX (Voice Operated TX)
Allows your radio to transmit with the sound of your voice for
P/A Mode
Allows your radio to become a public address system with an optional external speaker connected. In this mode only microphone audio heard over the optional external speaker when the
Mode Operation and Function Set Up
Depending on how your Dealer has programmed your radio, you may be able to change certain modes and functions of your radio. Consult with your radio communications Dealer regarding which functions are available with your radio.
The following identifies display prompts for various radio functions. NOTE: All functions are activated or turned off by pressing the MODE button. Use the up or down buttons to toggle through the choices available with each function. To exit, press the MODE or
Power On
Power on the radio by turning the power / volume control knob clockwise out of detent. The radio will perform a
Channel Change
Press and release the up or down. Your display will change with each channel selection, and will vary depending on how your Dealer programmed each channel description. A press and hold of up or down will scroll trough the channels.
Transmit
Press the
Channel Option View
In receiving mode, if the MON (monitor) button is pressed for more than 2 seconds, the RX tone option and the TX tone option for each channel selected will display.
This display example identifies:
RCTC 01 Receive, CTCSS, Tone 1
This display example identifies:
TOCS 023 Transmit, DCS, Code 023
Channel Option Settings Menu
NOTE: These setting instructions are
If the
The Channel Options Settings menu and
and TWO TONE .
Scroll through the
TONE SET settings include: RX TONE
TX TONE
ENGLISH
6