GAS CONVERSION KITS
WARNING: THIS CONVERSION KIT SHALL BE INSTALLED BY A QUALIFIED SERVICE AGENCY IN ACCORDANCE WITH THE MANUFACTURER'S IN- STRUCTIONS AND ALL APPLICABLE CODES AND REQUIREMENTS OF THE AUTHORIZED HAVING JURISDICTION. IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE, EXPLOSION OR PRODUCTION OF CARBON MONOXIDE MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. THE INSTALLATION IS NOT PROPER AND COM- PLETE UNTIL THE OPERATION OF THE CONVERTED APPLIANCE IS CHECKED AS SPECIFIED IN THE OWNER INSTRUCTIONS SUPPLIED WITH THE KIT. THE QUALIFIED SERVICE AGENCY PERFORMING THIS INSTALLATION ASSUMES RESPONSIBILITY FOR THIS CONVERSION.
AVERTISSEMENT: CET ÉQUIPEMENT DE CONVERSION SERA INSTALLÉ PAR UNE AGENCE QUALIFIÉE DE SERVICE CONFORMÉMENT AUX INSTRUCTIONS DU FABRICANT ET TOUTES EXIGENCES ET CODES APPLICABLES DE L'AUTORISÉSAVOIRLAJURIDICTION. SIL'INFORMATION DANS CETTE INSTRUCTION N'EST PAS SUIVIE EXACTEMENT, UN FEU, EXPLOSION OU PRODUCTION DE PROTOXYDEDECARBONEPEUTRÉSULTERLEDOMMAGES CAUSER DE PROPRIÉTÉ, PERTE OU BLESSURE PERSONNELLE DE VIE. L'AGENCE QUALIFIÉE DE SERVICE EST ESPONSABLE DE L'INSTALLATION PROPRE DE CET ÉQUIPMENT. L'INSTALLATION N'EST PAS PROPRE ET COMPLÉTE JUSQU'À L'OPÉRATION DE L'APPAREIL CONVERTI EST CHÉQUE SUIVANT LES CRITÈRES ÉTABLIS DANS LES INSTRUCTIONS DE PROPRIÉTAIRE PROVISIONNÉES AVEC L'ÉQUIPEMENT.
In Canada:
THE CONVERSION SHALL BE CARRIED OUT IN ACCORDANCE WITH THE REQUIREMENTS OF THE PROVINCIAL AUTHORITIES HAVING JURISDICTION AND IN ACCORDANCE WITH THE REQUIREMENTS OF THE
AND .2 INSTALLATION CODE.
LA CONVERSION DEVRA ÊTRE EFFECTUÉE CONFORMÉMENT AUX RECOMMANDATIONS DES AUTORITÉS PROVINCIALES AYANT JURIDICTION ET CONFORMÉMENT AUX EXIGENCES DU CODE D'INSTALLATION CAN1- B149.1 ET.2.
Gas conversion kits are available to adapt your appliance from the use of one type of gas to the use of another. These kits contain all the neces- sary components needed to complete the task including labeling that must be affixed to en- sure safe operation.
Kit part numbers are listed here and the following steps detail the conversion procedure.
Step 1. Turn off the gas supply to the appliance.
Step 2. Carefully remove the logs. Exercise care so as not to break the logs.
Step 3. Refer to Figure 47.
Remove the burner assembly with attached venturi tube.
Natural To Propane Gas Conversion Kit
Models No. | Unit Type | Catalog No. |
|
|
|
MPLDV30 | millivolt | H6163 |
|
|
|
MPLDV35 | millivolt | H6975 |
|
|
|
MPLDV40 | millivolt | 85L59 |
|
|
|
MPLDV45 | millivolt | 85L69 |
|
|
|
MPLDV30 | electronic | H6166 |
|
|
|
MPLDV35 | electronic | H6973 |
|
|
|
MPLDV40 | electronic | H6168 |
|
|
|
MPLDV45 | electrnoic | H6169 |
|
|
|
Propane to Natural Gas Conversion Kit
Model No. | Unit Type | Catalog No. |
|
|
|
MPLDV30 | millivolt | H6165 |
|
|
|
MPLDV35 | millivolt | H6968 |
|
|
|
MPLDV40 | millivolt | H6177 |
|
|
|
MPLDV45 | millivolt | 85L62 |
|
|
|
MPLDV30 | electronic | H6170 |
|
|
|
MPLDV35 | electronic | H6974 |
|
|
|
MPLDV40 | electronic | H6172 |
|
|
|
MPLDV45 | electronic | H6173 |
|
|
|
Millivolt Appliances
Step 4. SIT Systems - Refer to Figure 48 on page 29 and the instructions provided with the kit. Using a Torx T20, remove and discard the three pressure regulator mounting screws. Remove the pressure regulator, spring, pop- pet, diaphragm and bushing. Discard all removed components.
Ensure the rubber gasket installed on the back of the replacement pressure regulator is prop- erly positioned and install the new pressure regulator using the new screws supplied with the kit. Tighten screws to 25 In. lb. torque.
Burner Assembly |
Orifice |
Gas Valve |
Assembly |
Air Adjustment |
Arm |
Figure 47 |
28
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
