Oil Piping -
--FILL PIPE
--AIR VENT
_o_1 | II TANKI | v_l | 8ft(2.4m) | |
ol II | 111S"UT'OFFI "Maximam | |||
| IL |
| VALVE | I One Pipe Lift |
Oil | Piping | System |
| |
AIR VENT |
|
|
|
|
|
|
| FUEL PUMP | |
FILL PIPE | "'',_ R |
| / | AUX |
|
| RETURN | m/ | .FILTER |
_II | I | PIPE _ | _ | INLET |
-
| (76ram'102mm) I |
.... F_iF_E 14 | R |
outside tank fuel pump above bottom of tank.
_o Oo °°8° _o °o °o_o °o o_
Figure 15
To determine the correct tubing size for piping, refer to table 3
| Table 3 |
| |
Line Length | Pipe Diameter (OD Tubing) |
3/8" (10 mm) | |
1/2" (12 mm) |
When using a
mm)Hg to 15" (381 mm) Hg. Both conditions require that you use of a
Use continuous lengths of heavy wall copper tubing or steel pipe for oil supply pipe. Install oil supply pipe under floor or near walls to protect it from damage, Avoid running pipes along joists or reverberating surfaces. Always use flare fittings. All fittings must be accessible, Do not use compression fittings.
Figure 16
IMPORTANT
Table 4
3450 RPM - 3 GPH (11.4 LPH)
|
| Single- | Two- | Single- | Two- | |||||
|
| Stage | Stage | Stage | Stage | |||||
Lift "H" | 3/8" (10 mm) OD | 1/2" (12 mm) OD | ||||||||
ft (m) | Tubing - ft (m) |
| Tubing |
|
| |||||
0' (0.0) | 84 | (25.6) | 93 | (28.3) | 100 | (30.5) | 100 | (30.5) | ||
2' (0.6) | 73 | (22.3) | 85 | (25.9) | 100 | (30.5) | 100 | (30.5) | ||
4' (1.2) | 63 | (19.2) | 77 | (23.5) | 100 | (30.5) | 100 | (30.5) | ||
6 | '(1.8) | 52 | (15.8) | 69 | (21.0) | 100 | (30.5) | 100 | (30.5) | |
8' (2.4) | 42 | (12.8) | 60 | (18.3) | 100 | (30.5) | 100 | (30.5) | ||
10'(3.0) | 31 | (9.4) | 52 | (15.9) | 100 | (30.5) | 100 | (30.5) | ||
12'(3.7) | 21 | (6.4) | 44 | (13.4) | 83 | (25.3) | 100 | (30.5) | ||
14'(4.3) |
| 36 | (11.0) | 41 | (12.5) | 100 | (30.5) | |||
16'(4.9) |
| 27 | (8.2) |
|
| 100 | (30.5) | |||
18'(5.5) | ......... |
|
|
|
|
| 76 (23.2) |
Page 11
O23V SERIES