FTG Mode via CPU (Cont.)
Teaching FTG Configuration to a TV
This procedure describes how to “Teach” an FTG Configuration file from a USB memory device to a TV. Ensure you have completed the procedure on the previous page to create the FTG Configuration file before proceeding with the steps below.
Note: If the TV EBL is already in FTG Mode, you cannot use this procedure to make changes to the FTG Channel Map and FTG Installer Menu settings. You must use a direct
Note: If the preceding condition applies, but you wish to switch the TV to FTG mode via CPU, refer to Reference section, “Restoring Factory Defaults on the TV(s),” for further information before proceeding.
1.Turn ON the Target LQ630H or CQ610H TV.
If the Express Script Installer Menu Wizard appears on the screen when you turn ON the TV, use the Up/Down arrow keys on the Installer Remote to select Exit Express Script, and press OK (Enter).
2.Insert the USB memory device that contains the FTG Configuration file into the TV’s USB IN port.
3. | Press MENU on the Installer Remote to display the TV setup menus (TV is |
| USB Download Menu |
|
| ||||||
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| ||||
| in |
| Upgrade TV Software |
|
| ||||||
|
| Upgrade PTC Software |
|
| |||||||
4. | Use the arrow navigation keys to select/highlight either the Option menu icon |
|
|
| |||||||
| Teach To TV (TLL) |
|
| ||||||||
| from the TV setup menus or the Lock menu icon from the Function Menu. |
|
|
|
|
|
|
|
| ||
|
| Teach To TV (TLX) |
|
| |||||||
| Then, press the number “7” key a total of seven times to display the USB |
|
|
| |||||||
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| |||
| Download Menu. |
|
| CC | Previous | Enter | |||||
5. | Use the Up/Down arrow keys to select Teach To TV (TLX), and then press |
|
|
|
|
|
|
|
| ||
| Teach To TV (TLX) |
|
| ||||||||
| OK (Enter). |
|
|
| |||||||
6. | Use the Up/Down arrow keys to select the FTG Configuration file you want |
|
|
|
|
| |||||
|
|
|
|
| |||||||
|
|
|
|
|
|
|
| ||||
| to install, and then press OK (Enter). |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |||
| Teaching status will be shown on a progress bar in a new window. Do NOT |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |||
|
| CC | Previous | Enter | |||||||
| remove the USB device until Teaching is complete. When the Teaching |
| |||||||||
|
|
|
|
|
|
|
|
| |||
| process is complete, the USB Download Menu will reappear on the screen. |
|
|
|
|
|
|
|
|
| |
|
|
|
|
| Teach To TV |
|
| ||||
7. | When Teaching is done, press CC on the Installer Remote to exit the USB |
|
|
|
|
|
| ||||
|
|
| UPDATING... |
|
| ||||||
| Download Menu, remove the USB memory device from the Target TV, and |
|
|
|
|
| |||||
|
|
|
|
|
|
| 50% |
|
| ||
| turn OFF the TV. |
|
|
|
|
|
|
|
| ||
|
|
|
| Do not unplug! |
|
| |||||
8. | After a few seconds, turn ON the TV, and verify that the FTG Configuration |
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
| |||
| is now resident on the Target TV. |
|
|
|
|
|
|
|
|
| |
The Target TV CPU is now in FTG Mode (if it was previously in
Note: When you turn it back ON, the TV will tune according to the Start Channel setting in the Installer Menu. If a Start Channel is specified, the TV will tune to that channel; otherwise, the TV will tune to the lowest logical channel in the FTG Channel Map.
46 |