Piping Length and Elevation | LG Electronics LA090HPO, LA120HPO

Installation

PipingLengthandElevation

	Capacity	Pipe Size		Standard	Max.	Max.	Additional
	Capacity			Length	Elevation	length	Refrigerant
	(Btu/h)	Suction	Evap	Length	Elevation	length	Refrigerant
	(Btu/h)	Suction	Evap	m(ft)	B m(ft)	A m(ft)	g/m(oz/ft)

	9k, 12k	Ø12.7mm(1/2")	Ø6.35mm(1/4")	7.5(25)	7.5(25)	15(49)	20(0.22)

Indoor unit

B

A

Outdoor unit

A

Indoor unit

Outdoor unit

Outdoor unit

	Oil trap	A
	Oil trap
B	Indoor unit

B

If piping length is more than 16.4ft(5m)

CAUTION: Capacity is based on standard length and maximum allowance length is on the basis of reliability.

Oil trap should be installed every 16.4~23feets (5~7 meters).

16Room Air Conditioner

Image 16

LG Electronics LA090HPO, LA120HPO Piping Length and Elevation, Oil trap should be installed every 16.4~23feets 5~7 meters

Contents

Room Air Conditioner Table of Contents Safety Precautions InstallationDo not use damaged power cords, plugs, or a loose socket Install the panel and the cover Do not install the product on a defective installation stand Operation When flammable gas leaks, turn Do not place a heater or otherDo not use the product in a tight Sounds, odors, or smoke comes Keep level even when installing That water is drained away prop Product when removing Do not use the product for speCial purposes, such as preserv Ing foods, works of art, etc. It is a Outlet while the air conditioner is DisuseIt is not sanitary and could cause Symbols Used in this Manual DimensionsIndoor Unit Outdoor Unit 9k, 12k Models Product Specifications Models Installation Parts InstallationInstallation Tools Installation Map Confirm The Refrigerant This Product Contains R-410A Refrigerant Rooftop Installations Select the best LocationIndoor unit Outdoor unit Oil trap should be installed every 16.4~23feets 5~7 meters Piping Length and Elevation Preparing Work for Installation Open panel frontCover pipe and cover side remove Drain hose junction Fixing Indoor Unit Pipe and the wire. Refer to installationCase of nothing wrong, connect Flaring work and connection of piping Flaring Work Connecting the Piping CheckIndoor Foamed polyethylene or equivalent is recommended Wrap the insulation material around the connecting portion Indoor unit tubing Flare nut Pipings For right piping. Follow the instruction below Good case Bad case Connection of Piping -Outdoor Connecting the Cables Connection method of the connecting cableExample How to connect wiring to the terminals Connecting the cable between indoor unit and outdoor unit To check the drainage Checking the DrainageDrain piping Forming the Piping Air purging Air PurgingAir purging with vacuum pump Evacuation Soap water methodFinishing the job Charging Panel Front Assembly Prepare remote controller Test RunningSettlement of outdoor unit Evaluation of the performance Pump Down Procedure Pump Down How to replace picture & photograph Operation Functions Time delay Safety Control Chaos Swing ModeCooling Operation Mode Function of main control Auto Operation Electronic control mode Auto Operation for Cooling Auto Operation for Dehumidificationonly Heating Model Healthy DehumidificationAuto Operation for Heatingonly Heating Model Heating Operation Modeonly Heating Model Hot-Start Control Cooling Mode with the Sleep Mode Cooling or Heating Mode with Sleep Mode Auto ControlHeating Mode with the Sleep Modeonly Heating Model Auto restart Forced OperationCooling Heat pump Model Test operation Signal Receptor Display FunctionSelf-diagnosis Function Operation Indication Lamps Controls Remote Control OperationsNd F Button To remove the Grille from the Chassis DisassemblyTo remove the Control Box Before removing the Turbo Fan To remove the Evaporator. Remove hole tubing holdeTo remove the Motor Schematic Diagram Heat Pump/Cooling Only SeriesIndoor Unit Heat Pump Series/ Cooling Only Series Outdoor Unit Indoor Unit P.W.B. Assembly No A20999A PCB ASSEMBLY, Main Top View Bottom View Outdoor Unit P.W.B. Assembly No A20901C PCB ASSEMBLY, Main Top View Bottom View No A20921A PCB Assembly Display P.W.B. ASM Wiring Diagram Outdoor UnitCooling Only Models, & Heating Models Troubleshooting Guide Refrigeration Cycle Diagram Piping Length and Elevation Procedure Way ValvePumping Down Air purging of the charge hose Re-air purging Balance refrigerant of the 3-way valve Gas leakage Evacuation All amount of refrigerant leaked Gas Charging After EvacuationConnect the charge hose to the charging cylinder Purge the air from the charge hose Method of using graph Method of using equationAccording to Indoor & Outdoor Temperature Additional gas charging Cycle Parts Trouble analysis Electronic Parts 9k model Product does not operate at all Product is not operate with the remote controller Compressor/Outdoor Fan are unable to drive When indoor Fan does not operate Nector When Vertical Louver does not operate When a comunication error occurs Phenomena in case of connecting error Indoor Unit Outdoor Unit Voltage of Connectors according to Indoor Fan Speed RY-COMP-B Exploded View Indoor Unit Outdoor Unit Replacement Parts List Parts ListIndoor Parts ListOutdoor December No A20926C