Manuals / Brands / Computer Equipment / Power Supply / Liebert / Computer Equipment / Power Supply

Liebert GXT3-10000T220 L1 L2 GET X1 X2, UPS Input ~ Output ~ BYP L1 L2, Bypass Input ~ X4X3

1 32

Download 32 pages, 2.06 Mb

Installation

9

3.4 External Electrical Connections

The external electrical connections may be accessed by removing the protective panel on the rear of

the UPS (see Figure 2) (panel ships loose from factory). Select a conduit knockout appropriate for

your cabling, based on local electrical codes.

Figure 4 Side view

3.5 Connecting Utility and Load

Connect the utility supply to the input terminals of the UPS. If the Liebert® GXT3-10000T220™ is

supplied by single-phase utility, connect the live phase to input L1.

3.6 Terminal Blocks for UPS

Figure 5 Single source input supply—input and output connections

!

WARNING

Before removing electric protective panel, ensure that the UPS is isolated.

NOTE

Once installation has been completed, adjust leveling feet to prevent the UPS from moving.

!

CAUTION

Power is connected through the input breaker, even when the UPS is in bypass mode.

Opening the input breaker when in bypass mode will disconnect output power to the

connected load.

Rear Panel

Cable Entry Cover

L1 L2 GET X1 X2UPS Input ~ Output ~BYP L1 L2Bypass Input ~X4X3

Single Feed

Jumper

120

208

220

120

0

240

Contents

Main Page TABLE OF CONTENTS FIGURES TABL ES IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Page Leakage Current NOTICE Information for the Protection of the Environment 1.0 INTRODUCTION AND SYSTEM DESCRIPTION 1.1 Device Overview The following table provides an overview of the various versions of the device: Figure 2 Liebert GXT3-10000T220 front and rear views Table 1 Overview of UPS devices and batteries 2.0 UNPACKING THE UPS AND SITE PREPARATION 2.1 Inspection 2.2 Required Setup Equipment 2.3 Unpacking Storage 2.4 Environmental Conditions 2.5 Access to Area 2.6 Floor Loading 2.7 Inventory List 3.0 I 3.1 Electrical preparations 3.2 Suggested Cable Sizes 3.3 External Protection and Isolating Devices 3.4 External Electrical Connections L1 L2 GET X1 X2 3.5 Connecting Utility and Load 3.6 Terminal Blocks for UPS UPS Input ~ Output ~ BYP L1 L2 Bypass Input ~ X4X3 L1 L2 GET X1 X2 UPS Input ~ Output ~ BYP L1 L2 Bypass Input ~ X4X3 3.7 Connecting Power Cables 3.8 External Battery Cabinets 4.0 O 4.1 Block Diagram 4.2 Control Panel 4.2.1 Controls and Messages Lighted LEDs Flashing LED NOTICE Operation 14 Figure 11 Menu tree Table 3 Displayed textsystem block and main menu 4.2.2 Battery Setup Parameters 4.2.3 Warning Indicators Table 4 Battery setup parameters Table 5 Warning indicators Table 3 Displayed textsystem block and main menu (continued) 4.2.4 Fault Indicators 4.3 Initial UPS Startup Procedure 4.4 UPS Shutdown Procedure 4.5 Maintenance Bypass Procedure 4.6 Return from Maintenance Bypass 4.7 Maintenance Breaker, Off Position 4.8 Self-Tests 4.8.1 Lamp Test 4.8.2 Battery Test 5.0 M 5.1 Test, Replacement and Disposal of Batteries 5.2 Storage 5.3 Cleaning 6.0 C 6.1 Communication Interface Port 6.2 Dry Contact 6.2.1 Any Mode Shutdown (Low Battery Warning) (On-Battery Warning) 6.3 Liebert IntelliSlot Communication Cards 6.3.1 Liebert MultiLink 6.4 Remote Emergency Power Off REPO switch connection diagram 7.0 T 8.0 S Table 9 Lieb ert GXT3 specifications Table 10 Battery cabinet specifications Table 11 Typical battery run times for the Liebert GXT3-10000T230 9.0 PRODUCT WARRANTY REGISTRATION Ensuring The High Availability Of Mission-Critical Data And Applications.